background image

7 Maintenance

 

 

7-1. Maintenance intervals and items 

 

 

- 37 - 

 

 
 
 
 
 

Maintenance 

 
 
 
 
The gas detector is an important instrument for the purpose of safety. 
To maintain the performance of the gas detector and improve the reliability of safety, perform a regular 
maintenance.  
 
 
 

7-1. Maintenance intervals and items 

 

 

Daily maintenance: Perform maintenance before beginning to work. 

 

Monthly maintenance: Perform maintenance on the alarm circuit (alarm test) once a month. 

 

Regular maintenance: Perform maintenance once or more for every six months to maintain the 
performance as a safety unit. 

 

Maintenance 

item 

Maintenance content 

Daily 

mainte-

nance 

Monthly 

mainte- 

nance 

Regular 

mainte- 

nance 

Power Supply 
Check 

Check that the power lamp lights up. 

 

 

 

Concentration 
Display Check 

Check that the concentration display value is zero (or 
20.9 vol% on the oxygen meter). When the reading is 
incorrect, perform the zero adjustment (or span 
adjustment) after ensuring that no interference gases 
exist around it. 

 

 

 

Flow rate 
check 

Check the flow rate to find abnormalities. 

 

 

 

Filter check 

Check the dust filter for dust or clogging. 

 

 

 

Alarm Test 

Inspect the alarm circuit by using the alarm test function. 

 

 

 

Span 
Adjustment 

Perform the span adjustment by using the calibration 
gas. 

 

 

 

Gas Alarm 
Check 

Check the gas alarm by using the calibration gas. 

 

 

 

 
 

 

Summary of Contents for SD-1DOX-AS






































































Reviews: