background image

 

Preface 

This manual includes hardware description and operation introduction of equipment. For your and other 
people’s safety, please read the manual carefully. 

 

Pay attention 

Pay attention to the words after the signs below.   

Sign 

Description 

 

The words after this sign means there is great potential danger, which 
may cause major accident, damage or even death, if it is not followed.   

 

The words after this sign means there is some potential danger, which 
may cause hurt or property lose, if it is not followed.   

 

The  words  after  this  sign  means  there  is  potential  risk,  which  may 
cause equipment fault or break, if it is not followed.   

 

 

Version 

Version YF-TAE-0099, A0, Released at 14th, Aug., 2017. 

The contents of this manual are updated irregularity for updating of product. The manual is only used as 

operation guide, except for other promises. No warranties of any kind, either express or implied are 

made in relation to the description, information or suggestion or any other contents of the manual. 

The images shown here are indicative only. If there is inconsistency between the image and the actual 
product, the actual product shall govern.

 

 

 

 
 
 
 
 
 
 
 

Summary of Contents for LGK 100IJ


















Reviews: