RINGFEDER TNM G Installation And Operation Manual Download

Page: 17 / 24

- 17 -

Trouble

Cause

Risk Warning

Correction

Unaccept-

able

tempera-

tures

Material proper-

ties of elastic

buffers change.

The torque

transmission

capability is

adversely af-

fected.

Disconnect drive

Replace elastomer

Re-align coupling

Adjust ambient temperature

Contact

with

aggressive

products

Material proper-

ties of elastic

buffers change.

The torque

transmission

capability is

adversely af-

fected.

Disconnect drive

Check coupling parts for damages

and replace parts, if necessary

Replace elastomer

Verify alignment of coupling

Prevent contact with aggressive

products

Torsional

vibrations

in the drive

line

Considerable

increase in

coupling tempera-

ture. Premature

wear of elastic

buffers. Increased

reaction forces act

on connected

machines.

Disconnect drive

Analyse and eliminate cause for

torsional vibrations

Check coupling parts for damages

and replace parts, if necessary

Replace elastomer and consult

RINGFEDER POWER

TRANSMISSION

concerning even-

tual use of another Shore-hardness

Verify coupling alignment

Claw break-

age

Wear limit

of elas-

tomer

exceeded

===>

contact of

claws

Coupling is

destroyed.

Connected

machines can be

affected, too.

Disconnect drive

Replace coupling

Inspect the elastomer for wear at

shorter intervals

Overload

due to too

high torque

Coupling is

destroyed.

Connected

machines can be

affected, too.

Disconnect drive

Verify coupling design in coopera-

tion with

RINGFEDER POWER

TRANSMISSION

Replace coupling

Install larger coupling, if necessary

RINGFEDER

TNM E

BAWN 002-GBR-2

Summary of Contents for TNM G

























Search results

Summary of Contents for TNM G

Reviews:

Related manuals for TNM G

Brands by name

Popular brands

RINGFEDER TNM G, Installation And Operation Manual

Search results

Summary of Contents for TNM G

Reviews:

Related manuals for TNM G

Brands by name

Popular brands