RINGSPANN DH 012 FEM Installation And Operating Instructions Manual Download | Manualshive

Page: 16 / 16

background image

Installation and Operating Instructions for

Brake Caliper DH 012 FEM, cCSAus

spring activated

– electromagnetic released

E 09.766e

Issue: 20.03.2019

Version : 1

drawn:MAYA

checked: Ei

Pages: 16

Page: 16

12. EC-Declaration of Conformity

Note regarding EMC Directive 2014/30/EU

The brake is an uncritical equipment according to the EMC-Directive because of its passive
operation. The brake can not be operated independently. After integration into a complete
system, the brake can be evaluated according to EMC-Directive. To comply with DIN EN 61000-
6-4, the mounting of a line filter is required as a general rule.

Note regarding EC-Machinery Directive 2009/42/EC

The product is a component for installation in a machine according to the EC-Machinery Directive
2009/42/EC. Together with other components, the product can meet safety-related applications.
The necessary measures will emerge from the risk analysis of the machine. Built-in, the brake is
part of the machine and the machine manufacturer assesses the conformity of the safety device
on the Machinery Directive. The commissioning of the brake is only permitted if the machine
fulfills the Machine Directive.

EC-Declaration of Conformity

We hereby declare that the following products are developed, designed and manufactured by our
own responsibility.

RINGSPANN GmbH

Schaberweg 30-38

D-61348 Bad Homburg

Product:

Electromagnetic released disk brake

Designation:

DH012FEM

Sizes:

012

Types:

4457-1205, next digits 15 and higher - followed by 6 digits

Following standards and directives have been applied and complied with:

DIN VDE 0580

Electromagnetic devices and components

– General specifications.

2014/35/EU

Low-Voltage Directive

DIN EN 61000-6-2

EMC

– Immunity to inteference in industrial areas

CSA C22.2 No. 14-13

Industrial Control Equipment

UL 508

Industrial Control Equipment

The commissioning of the brake is only permitted when the machine complies with the EC-
Machinery Directive 2006/42 / EC.

ppa. Ernst Fritzemeier

RINGSPANN GmbH
Schaberweg 30-38
D-61348 Bad Homburg

Bad Homburg, 26.04.2018

«
...
14
15
16

Summary of Contents for DH 012 FEM

















Reviews:

No comments

Related manuals for DH 012 FEM

Brand: ABB Pages: 86

Brand: Parker Pages: 54

Brand: G-Lab Pages: 16

Brand: G&G Pages: 2

Brand: Labnet Pages: 12

Accublock D1301

Brand: Labnet Pages: 13

Brand: Parkside Pages: 58

Brand: Ebyte Pages: 7

Brand: Xtricity Pages: 4

Brand: Croplands Pages: 168

Brand: iFIT Pages: 2

Brand: Hanil Pages: 22

Brand: Landefeld Pages: 14

Brand: X Training Equipment Pages: 9

Brand: ML Accessories Pages: 6

Brand: Matrox Pages: 116

Brand: TDS Fitness Equipment Pages: 5

Brand: TC Electronic Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands