RINGSPANN RDZ DFO Series Installation And Operating Instructions Manual Download | Manualshive

Page: 18 / 21

background image

Installation and opreating instructios for tor-

sionally stiff gear couplings

RDZ…DTO/…DFO

E 06.705

As of: 12.08.2020

Version: 02

Signed: SCCE

Checked: SCHW

No. of pages: 21 Page: 18

Before filling the coupling with lubricant, the quantity must be measured in accordance with
table 9.2. After assembly of the flexible coupling halve, the lubricant should be applied in the
cavity between the hub (item 1) and the flexible coupling halve (item 2). This approach
should be carried out for all flexible coupling halves. Afterwards, seal (item 6) should be in-
serted and the two halves should be screwed together via fitting screws. Excess lubricant
must be completely collected and disposed of in an environmentally friendly manner.

Lubricant quantity

Size

RDZ … DTO (Full Flex)

RDZ … DFO (Flex Rigid)

lbs.

oz.

lbs.

oz.

0010

0.07

1.06

0.03

0.53

0015

0.13

2.11

0.07

1.06

0020

0.38

6.00

0.19

2.99

0025

0.51

8.11

0.25

4.06

0030

0.75

12.00

0.38

6.00

0035

0.99

15.87

0.50

7.94

0040

1.74

27.87

0.87

13.94

0045

2.38

38.10

1.19

19.06

0050

3.51

56.08

1.75

28.05

0055

4.26

68.08

2.13

34.05

0060

7.63

122.05

3.81

61.02

0070

14.00

223.98

7.00

112.00

0080

21.16

338.62

10.58

169.31

0090

29.32

469.14

14.66

234.58

0100

39.14

626.24

19.07

305.12

Table 9.2: Lubricant quantity

Attention!

You may not mix different lubricants. The lubricant must be replaced after 6
months.

To replace the lubricant, we recommend disassembling the flexible coupling halves and thor-
oughly cleaning all parts. The re-filling with lubricant should then subsequently take place as
described above.

«
...
16
17
18
19
20
...
»

Summary of Contents for RDZ DFO Series






















Reviews:

No comments

Related manuals for RDZ DFO Series

Brand: Palazzetti Pages: 112

Litmann Quality 3100

Brand: 3M Pages: 2

Brand: Nemalux Pages: 6

Brand: OBDLink Pages: 2

Brand: Ultraflex Pages: 3

Brand: Kellfri Pages: 12

MCX-C15 - MusicCAST Network Audio Player

Brand: Yamaha Pages: 65

Brand: Yamaha Pages: 24

Brand: Bartscher Pages: 20

Brand: Bartscher Pages: 24

Brand: H&S Pages: 32

Brand: KAM Pages: 5

Brand: Interacoustics Pages: 25

Brand: Hamilton Beach Commercial Pages: 32

Brand: Orliman Pages: 11

Brand: Qtx Pages: 4

Brand: Amico Pages: 20

Brand: Star Trac Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands