background image

  

iHeat Operation Guide: 12063-A 01-13 

  |   

9

Fan settings

For optimal performance 
the fan setting would 
be on ‘Auto’—fan is 

controlled by the system, i.e. 
only comes on when the system 
is heating the house. When the 
thermostat is running the fan, the 
fan blade symbol appears next to 
‘Fan’ on the screen to indicate the 
thermostat has the fan on.

There are additional fan settings 
that can be programmed.

 

-

Lo

, fan is continuously on low. 

Depending on the installation, 
in some instances better 
heating can be achieved with 
the fan running continuously 
on low—can help reduce cold 
spots. 

 

-

Med

, fan is continuously on 

medium. 

 

-

Hi

, fan is continuously on high. 

Changing the fan setting
1.  Press ‘System & Fan’. 

2.  Press ‘Fan’. 

3.  The current setting will flash, 

use the up/down keys to shift 
between Lo, Med, Hi, and Auto 
modes. 

4.  Press ‘Done’ to save the 

setting.

Changing the fan to circulate air 
on a hot day

If you want air to circulate through 
the house on a hot day do the 
following:

1.  Press ‘System & Fan’. 

2.  Use the up/down keys to 

toggle between ‘Heat’ and 
‘Off’, select the off setting 
(‘Off’ will flash).  

3.  Select ‘Fan’ and use the up/

down keys to toggle between 
the fan settings and select the 
desired fan speed. The screen 
display would look similar 
to that shown below—fan 
symbol would also display. 

Remember this is a manual 
override of the system so if you 
want to stop the fan you will need 
to go back into the fan menu and 
change ‘Fan’ back to auto.

Wed

System & Fan

More

1:27

20.

2

System

Off

PM

Fan

Med

Summary of Contents for iHeat





















Reviews: