background image

40

2.6.6 CHRONOTHERmOSTAT OF A DIFFERENT bRAND

The Rinnai boiler can work by connecting a chronothermostat (optional). Or it can work by connecting a chronothermostat 

(optional), keeping the Rinnai WiFi chronothermostat connected: in this second configuration the Rinnai command 

transfers  the  room  temperature  control  function  to  the  optional  chronothermostat.  In  order  to  connect  the  room 

thermostat of another brand to the boiler’s electronic board, a special connector (blue) is supplied as standard.

Installation of the chronothermostat (of a different brand)

Isolate  the  appliance  electrically  by  disconnecting  it  from  the  electrical 

socket:

• 

remove the front panel from the boiler body taking care not to damage 

the  pressure  gauge,  first  lifting  it  upwards  and  then  moving  it  away 

from the boiler body;

• 

remove the protective cover of the main electronic board (PCB) and 

connect the supplied cable to the CN17 port at the top right of the PCB;

• 

insert  the  cable  through  the  holes  provided  in  the  lower  part  of  the 

appliance casing and connect the secondary room chronothermostat 

to the cable installed;

• 

check that the type of chronothermostat connected is in ‘open contact’: 

if it is a ‘closed contact’ type it is necessary to modify the 

parameter 

nr.14 of menu B

;

• 

close the PCB protection cover and assemble the front panel;

• 

electrically  power  the  appliance,  switch  on  the  remote  control  and 
activate  the  heating  function  by  pressing  the  button 

:  the  boiler 

must be set on ‘flow temperature’mode (

); check if it operates 

correctly.

2.6.7 FILLING THE SySTEm

Once  the  hydraulic,  gas  and  electrical  connections  have  been  completed  and  the  drainage  system  is  connected, 

proceed with filling the boiler heating circuit by opening the special tap at the base of the boiler.

IMPORTANT

The  filling  of  the  circuit  must  be  carried  out  in  a  very  slow  way: 

this prevents the 

formation of air bubbles that cause slowdowns in the commissioning of the system and can cause 

more problems in the initial phase of use.

Once the boiler has been installed, before operating it, always make sure that the system is filled 

correctly and that the pressure gauge on the front panel indicates, when the heating circuit is still 

cold, values from the green sector (0.5 ÷ 1.5bar). In case of necessity, restore the correct values by 

operating the appropriate tap at the base of the boiler.
The boiler has a vent valve built-in, on the circulation pump: make sure the valve cap is loose and 

free to vent air.
Open the bleed valves of the hydraulic system and the radiators, bleeding air until only water 

comes out.
By connecting the power supply cable, the boiler performs an automatic venting cycle of 60-120 

min (and some internal control operations): during this phase, you do not have to press any button 

on the remote control until the cycle is completed (during this phase some symbols may light up 

on the display and/or disappear).

At the end of the venting cycle it is possible that the system pressure has fallen below the minimum recommended 

value: restore the correct value by acting on the load tap.
If the deaeration cycle is not sufficient to expel most of the air in the system, it is suggested to disconnect the power 

supply cable and reconnect it to repeat the boiler vent procedure.
In the first uses and with a certain regularity it is advised to check that the pressure gauge on the front panel always 

indicates a normal pressure value: if necessary top up the system by operating the filling valve and restore the system 

pressure.

Cable (blue) to connect

the room thermostat 

(of different brand)

Blue cable hole

Plug CN17

(Blue)

    Latches

Main electric board

Removing the front panel

Summary of Contents for REB-KBI2424FF





































































Reviews: