Rise RXD250 Instruction Manual Download | Manualshive

Page: 8 / 12

background image

8

Click on the input button.

Click on the Transmitter setup wizard button and follow the steps to set up

the transmitter.

ARMING SETTING

At the end of the wizard is the screen to set the motor arming procedure.

The recommended setting is Yaw Right which requires the yaw control to be

held to the right while the throttle is at 0 for 3 seconds to arm the motors.
Holding the Yaw control to the left will disarm the motors. There are several
other options available for arming/stopping the motors including using a
switch assigned to Channel 6.

«
...
6
7
8
9
10
...
»

Summary of Contents for RXD250













Reviews:

No comments

Related manuals for RXD250

Brand: BML Pages: 6

Brand: Flybrix Pages: 19

Brand: XK Pages: 2

Brand: Reely Pages: 68

Brand: IdeaFly Pages: 3

4Joy AHP+ 2,4 GHZ

Brand: Jamara Pages: 12

Brand: Navig[8]r Pages: 15

Brand: Yunyi-flight Pages: 9

Brand: tbs electronics Pages: 27

Brand: PARASIT STUDIO Pages: 9

Brand: Jamara Pages: 32

Brand: Dualsky Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands