background image

15

  Part 

#  Description

 1 RISE2050  Canopy
  2  RISE2051  Camera Board  & Antenna
 3 RISE2052  Camera Case 
  4  RISE2053  Screw Set (6)
  5  RISE2054  Motor Cap (4)
  6  RISE2055  Main Motor CW L/F, R/R (2)
 14  RISE2056  Main Motor CCW R/F, L/R (2)
  7  RISE2057  Prop Guards  (4)
 8 RISE2058  Main Frame 
 9 RISE2059  Props (4)
 10  RISE2060  Control Board w/ Dampers
 11  RISE2061  Dampers (4)
 12  RISE2062  Wall Guards (2)
 13  RISP2065  650 mAh LiPo Battery
  RISP2066 USB 

Charger 

  

RISJ2000 Transmitter 6-channel

    TACZ1003  MicroUSB Charge Cord

Goggle Parts

    TACZ5200  FPV-G1 Goggles w/o Monitor
    TACZ5610  FPV-G1 Head Strap
    TACZ5612  FPV-G1 Face Plate Foam

FPV Monitor Parts & Accessories

    TACZ5160  FPV-RM2 40ch 5.8 GHz Monitor
    TACZ1010  4G Class 10 Micro Memory Card
    TACZ5300  FPV 5.8 GHz RP-SMA Tx Antenna 
    

Short 

110 mm 

3dBi

    TACZ5305  FPV 5.8 GHz Cloverleaf Antenna 3dBi
    TACZ5600  FPV-RM2 Sun Shield
    TACZ5602  FPV-RM2 Tripod Mount

Other Optional Parts & Accessories

    TACZ5604  USB Micro SD Card Reader
    TACJ2650  TTX650 6-channel SLT Computer Transmitter

* The Ring Gates come with genuine 3M™ Command™ strips

so they can be mounted on a wall or ceiling.

OPTIONAL RACING GATE SYSTEM

SPARE PARTS

Checkered Flag Gate

Elevated Gate

Pylon Gate

RISP0003

RISP0005

RISP0004

Arch Gate

LED Ring Gate*

Ring Gate*

RISP0006

RISP0007

RISP0002

Command™ and 3M™ are trademarks of 3M, Inc.

Summary of Contents for Vision HOUSERACER

















Reviews: