Troubleshooting
Check & Error Display
86
3
F-01
A master has not been wrapped
around the Print Cylinder(Drum).
Place an original and start with the master-
making process.
If you leave the machine without a master
wrapped around the Print Cylinder(Drum),
malfunction may occur. Press the
key,
and then press the
key. Or perform
master-making operation to wrap a master
around the cylinder(drum).
F-02
The master currently wrapped around
the Print Cylinder(Drum) for print size
is larger than paper placed on the
Paper Feed Tray.
Press the
key, and then replace with
paper in larger size.
If you start to print without paper replacement,
the part outside the paper size smudges the
Pressure Roller. If you want to start printing
regardless of this problem, press the
key
or the
key.
To stop printing, press the
key.
4
d-05
A master roll has not been set or has
not been correctly set.
Set a master roll correctly and close the
Master Making Unit Cover.
)
p.68
If a rewound master has been wrinkled or has
worn off, cut the edge of the master straight
and then set the master again.
d-08
The Master Making Unit has not been
correctly set.
Set the Master Making Unit correctly.
)
p.68
d-09
The Master Making Unit Cover has not
been closed.
Pull out the Master Making Unit and close the
Master Making Unit Cover completely.
)
p.68
d-17
An inappropriate master roll has been
set.
Set a master roll specific to the machine.
The
section on the master core is
missing, or it has worn off, or it has
been tilted.
The
section on the master core contains
information needed for making masters.
If the machine cannot read the information, it
does not operate. Set a dedicated Master Roll
that has the
mark and is free from wear
and tilt.
5
d-07
The Master Disposal Box has not been
set or has not been correctly set.
Set the Master Disposal Box correctly.
)
p.71
8
F-37
Originals have been placed in the ADF
unit (option) in the Book shadow
editing.
Press the
key and then place an original
on the Stage Glass.
Or quit the Book shadow editing.
)
p.38
9
b-01
A card has not been set to the Key
Card Counter (option).
Set a card to the Key Card Counter.
Location
No.
Error No.
Cause
Action
Troubleshooting
Check & Error Display
87
When the indicator lights
Because the entire master roll has been consumed, set a new master roll.
When the indicator lights
Because the Master Disposal Box is full, remove the box and discard the ejected masters.
When the indicator lights
Because the Ink Cartridge becomes empty, replace with a new Ink Cartridge.
When the indicator lights
Check error numbers shown on the Error Number Display and contact your dealer.
When the indicator lights
Contact your dealer and take a periodic inspection.
10
b-22
Power to the Job Separator (option) is
off.
Turn on the power to the Job Separator.
b-23
The Job Separator (option) has run out
of tape.
Set new tape to the Job Separator.
b-24
A tape jam has occurred in the Job
Separator (option).
Check the Job Separator and remove the
jammed tape.
Non
b-31
Data send to the Linked Printer
(option) has failed.
• Check that the cables of the Linked Printer
and the machine have been correctly
connected to the hub, for example.
• If the cable connections are appropriate,
check the communication status of the
server and/or network.
• Check with the manager of the server or
network.
b-32
Power to the Linked Printer (option) is
off.
Another possible cause is an
inappropriate cable connection or
cable line disconnection.
• Check that the Linked Printer has been
switched on.
• Connect the cables correctly.
b-33
An IP address has not been set for the
machine.
Using the Custom Setting mode, set the IP
address for the machine.
F-05
An attempt is being made to print a
smaller number of copies than the
minimum print quantity.
Select a larger number of copies than the
minimum print quantity.
F-58
Because the RISORINC-NET has
been initiated, the Linked Printer
(option) cannot be used for output.
• To output from the machine
Press the
key, and then press the
key.
• To output from the Linked Printer.
Press the
key, wait for a while, and then
try again.
Location
No.
Error No.
Cause
Action
Riso Kagaku Technical Training Center Version
