background image

27

Contents

1.

Introduction .................................................................................................... 29

2.

Safety Instructions.......................................................................................... 30

3.

Indicators and Operating Controls............................................................... 33

3.1

Front Panel ............................................................................................... 33

3.2

Back Panel................................................................................................ 35

4.

Installation and Start Up ............................................................................... 36

4.2

Permanently connected unit RITTAL PMC UPS 6KVA   ....................... 36

4.3

Battery extension...................................................................................... 40

5.

Troubleshooting.............................................................................................. 42

6.

Maintenance.................................................................................................... 45

6.1

Operation.................................................................................................. 45

6.2

Storage...................................................................................................... 45

7.

Technical data................................................................................................. 46

7.1

Electrical specifications............................................................................ 46

7.2

Typical stored energy time (Battery mode) .............................................. 47

7.3

Dimensions and weights........................................................................... 47

7.4

Operating environment............................................................................. 47

7.5

Port connectors......................................................................................... 48

7.5.1

RS232 interface ................................................................................ 48

7.5.2

Relay interface (Option) ................................................................... 48

8.

Appendix ......................................................................................................... 26

Summary of Contents for PMC





























Reviews: