13
ASSeMBly AND
INStAllAtION
Please refer to the illustra-
tions (P to S) provided at the
front and back of this manual.
Please note that the installation
dimensions differ depending on
the appliance version (Figs Q)!
For more information about
installation, see also www.ritter-
werk.de/installation-notes.
Safety instructions
To avoid personal injury or
damage to the appliance, please
observe the following safety
instructions:
- This appliance may only
be assembled by qualified
personnel. ritterwerk will not
be held liable for the conse-
quences of improper and/or
incorrect assembly.
- The power cord must be
positioned to ensure that the
appliance can be fully folded
down into the drawer without
the cable becoming trapped.
The power cord must be
routed directly and without
obstruction from the built-in
system to the socket, which
must be mounted in the floor
unit.
- Unplug the cable from the
socket before assembly.
Installation conditions
The following dimensions repre-
sent minimum values:
- Drawer clearance width:
AES/BFS 62 SR/SL: 344 mm
AES/BFS 62 SR-H/SL-H:
392 mm
- Clearance height for drawer
base/crossbeam:
without baseplate: 75 mm
with baseplate:
83 mm
- Pullout clearance for front
edge of worktop/inner edge of
front drawer panel: 365 mm
(finger protector and left-over
holder not mounted)
- Appliance width:
AES/BFS 62 SR / SL: 342 mm
AES/BFS 62 SR-H / SL-H:
390 mm
The drawer base should be at
least 16 mm thick.
At a nominal length of 500 mm,
the drawer runners should have
a static load capacity of at least
40 kg.
Selecting a socket
Note:
A surface-mounted socket (that
complies with VDE/DIN 49440,
ÖVE, SEV) must be mounted
either on or behind the rear panel
at drawer height.
P
The power cord connection
to the socket should be routed
under the rear crossbeam or the
underside of the work top and as
high up as possible in the corner
of the floor cabinet's rear panel.
It must be possible to slide the
drawer in fully while the power
plug is in the socket.
The power plug must be eas-
ily accessible to the user to
ensure that the appliance can
be unplugged from the mains as
required (for example, prior to
cleaning).
Mounting the food slicer
Preparation:
•
Pull out the drawer until it
stops.
Q
Determine the position for the
food slicer in accordance with the
assembly drawing.
or
•
Position the appliance, when
folded, into the drawer.
The distance between the front
edge of the worktop and the
completely screwed-in buffer
screw (12) should be approx.
5 mm.
•
Mark the position of the front
and rear fastening brackets deter-
mined in this manner on the base
of the drawer.
•
Remove the appliance from
the drawer.
Execution:
•
Drill the four holes as marked
for assembling the appliance
onto the base of the drawer.
•
Mount the appliance using
four pan-head screws 4.0 x 16
(for drawer base 16 mm).
r
H variants:
If the slice carriage (11) touches
off the front edge of the worktop,
baseplates (a) and spacer
plates (b) can be placed under-
neath if necessary. In this case,
longer screws must also be used
for assembly.
Mounting retaining brackets
Q
Position the retaining brack-
ets (7) and (8).
S
Check the position by placing
the finger protector and the left-
over holder onto the correspond-
ing retaining bracket.
•
Mark the position of the holes
and then drill them.
•
Mount the two retaining brack-
ets using countersunk screws
(Phillips drive) PZ 3.5 x 12 (for
drawer base 16 mm).
Adjusting appliance position
•
Position the appliance as
described in BEFORE USING
THE APPLIANCE FOR THE
FIRST TIME.
• Turn the buffer screw (12)
until it just makes contact with
the front edge of the worktop (do
not clamp tight!).
•
Check the setup by folding
and unfolding the appliance
several times in succession.
English
Note:
All dimensions in the assembly
drawings stated in mm!
Summary of Contents for AES 62 SL
