IT
ALIANO
19
3.2
ACCENSIONE
Per accendere il fuoco si deve utilizzare come com-
bustibile legna ben secca spaccata molto sottile in-
sieme ai prodotti specifici disponibili in commercio.
Se si usa una quantità troppo esigua di legna op-
pure se la legna è tagliata troppo grossolanamen-
te, la camera di combustione non raggiungerà la
giusta temperatura di esercizio. Una combustione
difficoltosa può provocare una grande produzione
di fuliggine o lo spegnimento del fuoco quando si
richiude lo sportello.
La combustione può essere difficoltosa fino a
quando non si è scaldato il camino. Il tempo neces-
sario dipende da come è realizzato il camino e dalle
condizioni meteorologiche.
Per ottenere un’accensione veloce si deve aprire
completamente sia la maniglia scuoticenere sia la
regolazione dell’aria primaria, inserire in camera
di combustione circa 2 kg di legna spaccata sot-
tile incrociandola (circa 10 - 12 pezzi di piccola
pezzatura e di lunghezza 25 - 33 cm), accendere
e tenere socchiusa la porta fuoco (nel richiuderla
si deve tenere la maniglia in posizione chiusa fin-
chè il gancio non va a toccare il rullino di chiusura).
Dopo qualche minuto, una volta avviata bene la
combustione, si dovrà richiudere correttamente la
porta fuoco.
Durante il funzionamento, all’interno della stufa av-
viene una reazione di combustione tra il combusti-
bile (la legna inserita nella camera di combustione) e
il comburente (l’ossigeno presente nell’aria dell’am-
biente in cui è installata la stufa).
La stufa a legna realizza un tipo di combustione inter-
mittente: dopo avere acceso il fuoco la combustione
prosegue fino all’esaurimento del combustibile, ma
può essere mantenuta effettuando un’altra carica e
così via.
Il mantenimento della combustione nel tempo è ga-
rantito dal corretto funzionamento del camino il qua-
le permette di evacuare i fumi e contemporaneamen-
te di far alimentare la fiamma con l’aria comburente.
In questo modo le caratteristiche realizzative del ca-
mino influiscono in modo determinante sul corretto
funzionamento della stufa a legna. La combustione
di legna richiede che l’afflusso di aria all’interno della
camera di combustione avvenga in più punti diver-
si per ottenere la massima efficienza. In particolare
è presente una alimentazione di aria primaria, che
affluisce dalla parte superiore della camera di com-
bustione e una alimentazione di aria secondaria che
affluisce dalla parte posteriore della camera di com-
bustione.
L’aria primaria è l’aria principale, attraverso la cui re-
golazione si imposta la velocità di combustione e la
potenza termica dell’apparecchio.
L’aria secondaria permette la post-combustione
dei fumi generando ulteriore calore, abbattendo la
quantità di gas nocivi emessi e migliorando in questo
modo sia il rendimento che l’impatto sull’ambiente.
Una volta avviata la combustione non può essere in-
terrotta in modo sicuro, ma va in ogni caso lasciata
esaurire naturalmente con il consumo di tutto il com-
bustibile introdotto.
3.1 FUNZIONAMENTO
USO
3
ATTENZIONE!
Per il corretto funzionamento della stufa a legna verificare che il
passaggio di aria comburente nella presa d’aria della stufa, l’eventuale presa d’aria nel
locale e tutte le griglie per aerazione e ventilazione non siano ostruite.
ATTENZIONE!
E’ importante che la legna inizi ad ardere velocemente. L’accensione di un
grande quantitativo di legna in fase di accensione può provocare una grande produzione
di fumo e una rapida emissione di gas con conseguente danno alla stufa.
Summary of Contents for X Art Basic
