RKI Instruments 35-3001A-05 Series Operator'S Manual Download

Page: 24 / 24

24 • 35-3001A-05-XX CO

Sample-Draw Detector

Parts List

Table 4 lists replacement parts and accessories for the carbon dioxide sample-draw detector.

Table 4: Parts List

Part Number

Description

06-1248RK

Sample tubing, 3/16 in. ID x 5/16 in. OD, specify length

06-1248RK-03

Sample tubing, 3/16 in. ID x 5/16 in. OD, 3 feet (for calibration kit)

07-0110RK

Gasket for IR flow block

17-2670

Inlet fitting O-ring

17-2671

Inlet fitting front ferrule

17-2672

Inlet fitting back ferrule and tube nut

30-1016RK

Pump

33-0165RK

Hydrophobic filter

33-0167RK

Particle filter

57-1053RK-10

Amplifier

61-5040RK-02

IR CO

sensor, 0 - 5,000 ppm

61-5040RK-03

IR CO

sensor, 0 - 5% volume

61-5040RK-05

IR CO

sensor, 0 - 50% volume

61-5040RK-10

IR CO

sensor, 0 - 100% volume

71-0340

Operator’s Manual, 35-3001A-05-XX Sample-Draw Detector

81-0070RK-01

Calibration cylinder, 2000 ppm CO

in nitrogen, 34 liter steel

81-0070RK-03

Calibration cylinder, 2000 ppm CO

in nitrogen, 103 liter

81-0072RK-01

Calibration cylinder, 2.5% CO

in nitrogen, 34 liter steel

81-0072RK-03

Calibration cylinder, 2.5% CO

in nitrogen, 103 liter

81-0073RK-01

Calibration cylinder, 15% CO

in nitrogen, 34 liter steel

81-0073RK-03

Calibration cylinder, 15% CO

in nitrogen, 103 liter

81-0078RK-01

Calibration cylinder, 100% nitrogen, 34 liter steel

81-0078RK-03

Calibration cylinder, 100% nitrogen, 103 liter

81-1054RK

Regulator, demand flow, for 34 liter aluminum, 58 liter, and 103 liter
calibration cylinders (cylinders with internal threads)

81-1055RK

Regulator, demand flow, for 17 liter and 34 liter steel calibration cylinders
(cylinders with external threads)

Summary of Contents for 35-3001A-05 Series

























Search results

Summary of Contents for 35-3001A-05 Series

Reviews:

Related manuals for 35-3001A-05 Series

Brands by name

Popular brands

RKI Instruments 35-3001A-05 Series, Operator'S Manual

Search results

Summary of Contents for 35-3001A-05 Series

Reviews:

Related manuals for 35-3001A-05 Series

Brands by name

Popular brands