4
5
HOW TO USE
Applying Wax:
1. Read, understand and follow all steps
in BEFORE USE Section.
2. Install clean applicator pad cover onto
the buffer pad.
3. Follow wax manufacturers recom-
mended procedures for applying and
removing wax. Also note any special
waxing instructions that may accom-
pany your workpiece (vehicle, boat,
etc.). Grip buffer firmly and apply light
pressure onto workpiece, press on/off
switch until it ‘clicks’ once to begin.
Gradually increase the amount of pres-
sure applied to the workpiece as
needed. TO STOP, decrease the
amount of pressure applied to the
workpiece and press on/off switch
(until it ‘clicks’) again.
Note: Applying liquid wax can be messy,
wear appropriate clothing and safety
glasses or goggles. Remove all jewelry.
DO NOT wear loose fitting clothing. Wear
hair net to help prevent hair from being
caught up in the rotating buffer.
Removing Wax (buffing):
1. Read, understand and follow all steps
in BEFORE USE Section.
2. Follow wax manufacturers recom-
mended procedures for applying and
removing wax. Also note any special
waxing instructions that may accom-
pany your workpiece (vehicle, boat,
etc.). Grip buffer firmly and apply light
pressure onto workpiece, press on/off
switch until it ‘clicks’ once to begin.
Gradually increase the amount of pres-
sure applied to the workpiece as
needed. TO STOP, decrease the
amount of pressure applied to the
workpiece and press on/off switch
(until it ‘clicks’) again.
CARE AND MAINTENANCE
Follow these instructions carefully to avoid
scratching painted and/or finished sur-
faces.
1. Wash buffer pad covers after each use.
Hand wash with warm water and mild
detergent. Dry thoroughly. Repeat as
needed to remove all traces of wax, dirt,
and residue. Replace buffer pad cov-
ers when they become stiff or perma-
nently stained.
2. Store buffer housing with a clean, damp-
ened rag. Wipe dry with clean, dry rag.
11.Maintain auto polisher with care - Keep
auto polisher clean for better and safer
performance. Inspect auto polisher
cords periodically and if damaged, have
repaired by authorized service facility.
Inspect extension cords periodically
and replace if damaged. Keep handles
dry, clean, and free from oil and grease.
12.Disconnect auto polisher - When not
in use, before servicing, when chang-
ing pad cover.
13.Outdoor use extension cords - When
auto polisher is used outdoors, use
only extension cords intended for use
outdoors and so marked.
14.Avoid unintentional starting. Don’t carry
plugged-in auto polisher with finger on
switch. Be sure switch is off when
plugged in.
15.Stay alert - Watch what you are doing.
Use common sense. Do not operate
auto polisher when you are tired.
16.Check damaged parts - Before further
use of the auto polisher, a guard or
other part that is damaged should be
carefully checked to determine that it
will operate properly and perform its
intended function. Check for alignment
of moving parts, breakage of parts,
mounting, and any other conditions that
may affect its operation. A guard or other
part that is damaged should be prop-
erly repaired or replaced by an autho-
rized service center unless otherwise
indicated elsewhere in this instruction
manual.
17.Have defective switches replaced by
authorized service center.
18.Do not use auto polisher if switch does
not turn on and off.
19.Do not put fingers or any objects be-
tween the skirt and buffer pad while
polisher is on.
20.Do not allow the auto polisher to oper-
ate without it being held to or against a
stationary surface. The free wheeling
buffer pad can throw off the pad cover.
Storage
1. Store buffer with buffer pad covers re-
moved.
2. Store buffer and related chemicals in
clean, dry area that will not likely freeze.
Freezing temperatures is hard on
waxes.
Note: Ensure polisher is out of reach of
children at all times.
SPECIFICATIONS
Power Requirement: 120V AC / 60Hz
Rated Current: 0.5A
Speed: 2600 ± 10% rpm
Cord Length: 70.8”
Pad Diameter: 6”
90 DAYS LIMITED WARRANTY
For a period of ninety (90) days from date of purchase, Shinn Fu Co. of
America, Inc. will repair or replace, at its option, without charge, any of its products
which fails due to a defect in material or workmanship, or which fails to conform to any
implied warranty not excluded hereby.Performance of any obligation under this war-
ranty may be obtained by returning the warranted product, freight prepaid, to Shinn Fu
Co. of America, Inc. Warranty Service Department, 10939 N. Pomona Ave., Kansas
City, MO 64153.
Except where such limitations and exclusions are specifically prohibited by
applicable law, (1) the CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE
REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE,
and (2) Shinn Fu Co. of America, Inc. SHALL NOT BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER, and (3) THE
DURATION OF ANY AND ALL EXPRESSED AND IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, IS LIMITED TO A PERIOD OF NINETY (90) DAYS FROM
DATE OF PURCHASE.
Some states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or exclu-
sion may not apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
