Istruzioni per l´utilizzo
POWER PEAK TRIPLE EQ-BID
Art.N.
8541
15
IMPOSTAZIONE DELLA CORRENTE DI SCARICA
Premere il tasto ‘+’ fino a quando la freccia sul display affianca il campo “corrente di
scarica ”. Premere quindi il tasto ‘ENTER’; i simboli
‘+ / -‘ lampeggiano; è ora possibile impostare la
corrente di scarica ad intervalli successivi di 0,1 A
mediante i tasti ‘+ / -‘ . Una volta effettuata la sele-
zione premere nuovamente il tasto ‘ENTER’. La corrente di scarica può essere impo-
stata all’interno del campo di valori compresi tra 0,1 A fino a 1,0 A. L’intensità massima
della corrente di scarica è tuttavia dipendente dal numero di celle e dalla tensione della
batteria. Il processore interno all’apparecchio limita automaticamente l’intensità massi-
male della corrente di ricarica.
PRE-SELEZIONE DEL SEGNALE ACUSTICO
Premere il tasto ‘+’ fino a quando la freccia sul dis-
play affianca il campo “segnale acustico (cicalino)”.
Premere quindi il tasto ‘ENTER’; i simboli ‘+ / -‘
lampeggiano; è ora possibile selezionare mediante
i tasti ‘+ / -‘ la tonalità del segnale acustico che segnala, per esempio, il termine della
fase di ricarica. E’ possibile scegliere tra 5 tonalità differenti; in alternativa è anche pos-
sibile disattivare completamente il segnale acustico. Premendo il tasto ‘+’ o quello ‘-‘ si
imposta una nuova tonalità. La tonalità viene contemporaneamente emessa per agevo-
lare la selezione.
MEMORIZZAZIONE DELLE IMPOSTAZIONI
Premere il tasto ‘+’ fino a quando la freccia sul dis-
play affianca il campo “fine (termine)”
Le regolazioni effettuate in precedenza saranno
memorizzate nel dispositivo premendo il tasto
‘ENTER’. Il display mostra la schermata di avvio e torna nella schermata di uscita.
7.4
AVVIO DELLA PROCEDURA DI RICARICA / SCARICA
• Premere il tasto ‘MAN’; appare la schermata di
avvio
• Il tasto ‘ENTER’ permette di impostare la ricarica
per la posizione di memoria visualizzata
• Premere il tasto ‘MODE’ per selezionare il tipo di
procedura desiderata
• Vengono mostrati per sicurezza ancora una volta
sullo schermo i parametri memorizzati in prece-
denza
• Premere il tasto ‘START’ per avviare la proce-
dura; un segnale acustico conferma l’avvio della
stessa. Viene visualizzata in seguito la scher-
mata di lavoro comprendente tutti i parametri fon-
damentali (vedi cap. 5.1)
• I tasti ‘+’ o ‘-‘ consentono di modificare l’intensità della corrente mentre la procedura è in
corso. Il nuovo valore lampeggia prima di essere selezionato .
© robbe Modellsport
Summary of Contents for 8541
