background image

ENGLISH

3

Instructions and User Manual

CO N F O R M I T Y

Modellbau Lindinger GmbH hereby declares that this device complies with the essen-

tial requirements and other relevant regulations of the corresponding CE directives. 

The original declaration of conformity can be found on the Internet at www.robbe.

com, in the detailed product view of the respective device description or on request. 

This product can be operated in all EU countries.

WA R R A N T Y

Our articles are equipped with the legally required 24 months warranty. Should you wish to assert a justified war-

ranty claim, always contact your dealer, who is responsible for the warranty and the processing. During this time, 

any functional defects that may occur, as well as manufacturing or other problems, will be rectified.

Material defects corrected by us free of charge. Further claims, e.g. for consequential damages, are excluded.

The transport to us must be free, the return transport to you is also free. Freight collect shipments cannot be ac-

cepted. We cannot accept liability for transport damage and loss of your consignment. We recommend appropri-

ate insurance.

To process your warranty claims, the following requirements must be met:

•  Attach the proof of purchase (receipt) to your shipment.

•  The units have been operated in accordance with the operating instructions.

•  Only recommended power sources and original robbe accessories have been used.

•  There is no moisture damage, external interference, reverse polarity, overloading or mechanical damage.

•  Attach relevant information for finding the fault or defect.

This symbol means that small electrical and electronic devices must be disposed of at 

the end of their useful life, separated from the household refuse. Dispose of the device 

at your local municipal collection point or recycling centre. This applies to all countries 

of the European Union and other European countries with a separate collection 

system.

D I S P O S A L

I N S U R A N C E

Ground-based models are usually covered by personal liability insurance. Additional insurance or extension is 

required for aircraft models. Check your insurance policy (private liability) and take out suitable insurance if neces-

sary.

D I S C L A I M E R

Modellbau Lindinger GmbH cannot monitor compliance with the assembly and operating instructions or the 

conditions and methods for installation, operation, use and maintenance of the model components.Therefore, 

we accept no liability for losses, damage or costs arising from or in any way connected with incorrect use and 

operation. To the extent permitted by law, the obligation to pay damages, irrespective of the legal grounds, shall 

be limited directly to the invoice value of the claims arising from the event causing the damage.                      

D I S T R I B U TO R

Copyright 2019

Modellbau Lindinger 2019

Copy and reprint only with our permission.

Service-Address

 

Contact your Dealer or:

Modellbau Lindinger GmbH, Industriestraße 10, 4565 

Inzersdorf im Kremstal 

service@robbe.com, +43(0)7582-81313-0

www.robbe.com

S A F E T Y   I N S T R U C T I O N S   F O R   R E C H A R G E A B L E   B AT T E R I E S

•  Do not immerse the battery in water or other liquids.

•  Do not heat, throw into fire or microwave.

•  Do not short-circuit or charge with reversed polarity

•  Do not expose, deform or throw the battery to pressure

•  Do not solder directly on the battery

•  Do not change or open the battery

•  Only charge the battery with suitable chargers, never connect it directly to a power supply unit.

•  Never charge or discharge the battery or charger on a flammable surface.

•  Never leave the battery unattended during charging or discharging processes.

•  Never charge or discharge the battery in direct sunlight or near heaters or fire.

•  Do not use the battery in places subject to high static discharge.

All this can cause the battery to be damaged, explode or even catch fire!

•  Keep the battery away from children

•  Do not associate leaked electrolyte with fire, as it is highly flammable and may ignite.

•  The electrolyte liquid should not get into the eyes, if it does, rinse immediately with plenty of clear water and 

then see a doctor.

•  The electrolyte liquid can also escape from clothes and other objects with a lot of water or washed off

•  Observe the safety instructions of the battery manufacturer and the charger manufacturer.

Modellbau Lindinger GmbH

Industriestraße 10 

4565 Inzersdorf im Kremstal 

Austria

Phone: +43(0)7582/81313-0 

Mail: info@robbe.com

UID No.: ATU69266037

„robbe Modellsport“ is a registered Trademark by 

Modellbau Lindinger GmbH

Errors, misprints and technical changes reserved.

Summary of Contents for ARTR 1205













Reviews: