background image

3

Be sure to read these Safety Notes before 
you assemble your model. Always keep to 
the procedures and settings recommended 
in the instructions.

If you are operating a radio-controlled model 
aircraft, helicopter, car or boat for the first 
time, we recommend that you enlist an expe-
rienced modeller to help you.

Safety Notes

Radio-controlled models are not toys in the usual 
sense of the term. Young persons under four-
teen years should only be allowed to operate 
them under the supervision of an adult.

Building and operating these models requires 
technical expertise, manual skills, a careful atti-
tude and safety-conscious behaviour. 
Errors, negligence and omissions in building or 
flying these models can result in serious perso-
nal injury and damage to property.

Since the manufacturer and vendor are not in a 
position to check that your models are built and 
operated correctly, all we can do is bring these 
hazards expressly to your attention. We deny all 
further liability.

Aircraft propellers, and all moving 
parts generally, constitute a constant 
injury hazard.
It is essential to avoid touching such 
parts.

Please bear in mind that motors and 
speed controllers may become hot 
when operating. 
It is essential to avoid touching such 
parts.

Do not stand close to the hazard area 
around rotating parts when an electric 
motor is connected to the flight battery.
You must also take care to keep all other 
objects away from moving or rotating 
parts.

Observe the instructions provided by 
the battery manufacturer.

Overcharged or incorrectly charged 
batteries may explode. Take care to 
maintain correct polarity.

Ensure that the equipment is protected from 
dust, dirt and moisture. Do not subject the sys-
tem to excessive heat, cold or vibration.
Use the recommended charger only, and charge 
the batteries only for the prescribed period.

Check your equipment for damage at regular in-
tervals, and replace defective components with 
genuine spare parts.

Do not re-use any devices which have been da-
maged in a crash or by water, even when they 
have dried out again. 
Either send the equipment to the robbe Service 
Department for checking, or replace the parts in 
question. 
Crash or water damage can result in concealed 
defects which may lead to failure in subsequent 
use.

Use only those components and accessories 
which we specifically recommend.

Do not carry out modifications to the radio con-
trol system components apart from those descri-
bed in the instructions.

Building and Operating Instructions - ZLIN 50LX Red Bull 1600mm ARF 

No. FW004004

Summary of Contents for ZLIN 50LX RED BULL 1600MM ARF

















Reviews: