7
positioning is finished ,select
“Calibrate Values”
and press [ENTER]:
. Calibration via the control board
Select desired effect, press [ENTER] and adjust its right value (0 - 255). This can be repeated for each calibred
effect if it is required. When the calibration is finished, it is necessary to use the
“Save and Reset”
function to
write the calibration values to the memory and to make a reset in order to check the newly adjusted positions
of the calibrated effects.
List of the calibrated effects:
Yellow
Effect indexing
Mech. dimmer 2
Cyan
Conversion filter
Zoom
Magenta
Effect wheel
Mech. dimmer
. Calibration via the DMX controller
Connect the DMX controller to the fixture.Now you can calibrate the selected effect by your controller.
Effect
Mode 1
Mode 2
Mode 3
Mode 4 Mode 5
Cyan
channel
channel 9
channel 4
channel
channel
Magenta
channel 23
Channel 20
channel 25
channel 22
channel 22
Yellow
channel 4
channel
channel 6
channel 3
channel 3
Conversion filter
channel 25
channel 22
channel 27
channel 24
channel 24
Effect wheel
channel 6
channel 3
channel 8
channel 5
channel 5
Effect indexing
channel 27
channel 24
channel 29
channel 26
channel 26
Zoom
channel 28
channel 25
channel 30
channel 27
channel 27
Mech. dimmer
channel 9
channel 6
channel 3
channel 8
channel 8
Mech. dimmer 2
channel 30
channel 27
channel 32
channel 29
channel 29
After having calibrated required effects ,use the
“Save and Reset”
function to write the calibration values to
the memory and to make a reset in order to check the newly adjusted positions of the calibrated effects.
Item
„Load Default Values”
restores factory calibration values.
Updating software.
--- Using this function you can update software in the fixture via PC and serial link.
The following are required in order to update software:
- PC running Windows 95/98/2000/XP or Linux
- DMX Software Uploader
- Flash cable RS 232Robe (No.13050624)
Note1
:Software update should execute a qualified person.If you lack qualification, do not attempt the update
yourself and ask for help your ROBE distributor.
Note 2
:DMX address, IP address ,programs -3 and all functions in menu Personality will be set to their default
values.
To update software in the fixture:
1
.Installation of DMX Software Uploader.
1.
DMX Software Uploader program is available from the ROBE web site at WWW.robe.cz.
2
.Make a new directory ( e.g. Robe_Uploader) on your hard disk and download the software to it.
3
.Unpack the program from the archive.Program file has name:DSU_name of corresponding
fixture_SoftwareID.If the Robe fixture is produced in magnetic and electronic ballast version, the
name of DMX Software Uploader is the same for both versions.
SoftwareID describes the versions of fixture software included in DMX Software Uploader. Higher
number means later software versions.
2.
Fixture software updating.
1
.Determine which of your COM port is available on your PC and connect it with to the DMX input
of the fixture using the Flash cable. Do not extend this cable! Disconnect the fixture from the other
fixtures
in DMX chain! Turn on the computer and the fixture. Make sure that the lamp is switched off.
2
.Switch the fixture to the update mode by selecting the option Updating Software in menu Special
Functions on the fixture control panel.(From this option you cannot return back to the main menu.
If you do not want to continue in software update, you have to switch off and on the fixture to leave
this option!)
3
.It is recommended that you exit all programs before running this Software Uploader.
4
.Start the Software Uploader program. Select desired COM and then click Connect button.
If the conection is OK, click Start Uploading button to start uploading. It will take several minutes
to perform software update.If the option "Incremental Update"isn´t checked ,all processors will be
updated (including processors with the same software version).
If you wish to update only later versions of processors, enable the Incremental Update check box.
Avoid interrupting the process. Update status is being displayed in the list window.
When the update is finished, the line with the text “The fixture is successfuly updated‘ will appear
Summary of Contents for Color Wash 750 AT Tungsten
Page 1: ... Version 2 0 ...
Page 35: ...35 ...
