47
9. Maintenance
Interval
Part/Component
Maintenance work
Remark
Every 200
operating
hours
Valve clearance (intake valve
and exhaust valve)
Inspect / adjust
Request authorized
service station
Every year or
every 200
operating
hours
Fuel pipe
Replace
See ch. 9.3.7
The rubber buffers for vibration damping fitted between the
guide frame and the vibrator are parts subject to wear. They
must be replaced when necessary (porous, torn, damaged.
All externally accessible screws and nuts are to be checked for
tight fit approximately every 10 operating hours or daily.
9.2
Cleaning and care
Regular care and maintenance of the product will prolong its
service life significantly.
NOTICE
Risk of damage!
Cleaning the product with solvents, aggressive or combustible
cleaning agents may result in damage.
The use of high-pressure washers can result in damage
caused by water getting into the motor (silencer, air filter,
carburettor) and articulated joints of the product.
►
Do not use any solvents or aggressive, combustible clean-
ing fluids!
►
Do not use petrol for cleaning.
►
Do not use a jet of water or a high pressure washer.
NOTICE
Risk of engine damage!
Dirt or dust adhering to the cylinder fins can cause piston
seizure because heat cannot be dissipated.
►
Keep the cylinder fins free of dust or dirt.
1.
Clean the product regularly so that it does not suffer a pro-
duction outage due to dirt.
2.
Only use a damp cloth to clean the product. Only use water
and, if necessary, a mild detergent without any chemical
additives.
1)
Rubber buffer
2)
Screws
Summary of Contents for 62.05L
