SECTION 2: I
NSTALLER
R
ESPONSIBILITY
5 of 57
SECTION 2: INSTALLER RESPONSIBILITY
The installer is responsible for the follo
w
ing:
• To install the heater, as
w
ell as the gas and
electrical s
u
pplies, in accordance
w
ith applicable
specifications and codes. Roberts-Gordon LLC
recommends the installer contact a Local
B
u
ilding Inspector or Fire Marshal for g
u
idance.
• To
u
se the information given in a layo
u
t dra
w
ing
and in the man
u
al together
w
ith the cited codes
and reg
u
lations to perform the installation.
• To install the heater in accordance
w
ith the
clearances to comb
u
stibles.
• To f
u
rnish all needed materials not s
u
pplied as
standard eq
u
ipment.
• To plan location of s
u
pports, vents and air
intakes.
• To provide access for servicing.
• To provide the o
w
ner
w
ith a copy of this
Installation, Operation and Service Man
u
al.
• To never
u
se heater as s
u
pport for a ladder or
other access eq
u
ipment and never hang or
s
u
spend anything from heater.
• To ens
u
re there is adeq
u
ate air circ
u
lation
aro
u
nd the heater and to s
u
pply air for
comb
u
stion, ventilation and distrib
u
tion in
accordance
w
ith local codes.
• To provide a method that ens
u
res that the air flo
w
thro
u
gh the heat exchanger is
w
ithin the
acceptable range indicated on the serial plate
prior to energizing the heater, and that s
u
ch air
flo
w
contin
u
es at least 90 seconds after the
heater is de-energized.
• To ens
u
re the heater is placed in an approved
application.
2.1 Wall Ta
g
A laminated
w
all tag is incl
u
ded
w
ith the heater as a
permanent reminder of the safety instr
u
ctions and
the importance of the req
u
ired clearances to
comb
u
stibles. Affix the tag by peeling off the backing
of the adhesive strips on the rear s
u
rface and
position the tag on a
w
all near the heater.
A copy of the
w
all tag (P/N 91039831) is ill
u
strated
on the back cover.
Kno
w
yo
u
r model n
u
mber and installed
config
u
ration. Model n
u
mber and installed
config
u
ration are fo
u
nd on the heater serial plate
and thro
u
gho
u
t the Installation, Operation and
Service Man
u
al.
2.2 Corrosive Chemicals
Roberts-Gordon LLC cannot be responsible for
ens
u
ring that all appropriate safety meas
u
res are
u
ndertaken prior to installation; this is entirely the
responsibility of the installer. It is essential that the
contractor, the s
u
b-contractor, or the o
w
ner
identifies the presence of comb
u
stible materials,
corrosive chemicals or halogenated hydrocarbons*
any
w
here in the premises.
* Halogena
t
e
d
Hy
d
rocarbons
are a family of chemical
compounds characterized by the presence of halogen ele-
ments (fluorine, chlorine, bromine, etc.). These compounds are
frequently used in refrigerants, cleaning agents, solvents, etc. If
these compounds enter the air supply of the burner, the life
span of the heater components will be greatly reduced. An out-
side air supply must be provided to the burners whenever the
presence of these compounds is suspected. Warranty will be
invalid if the heater is exposed to halogenated hydrocarbons.
2.3 National Standards and Applicable Codes
All appliances m
u
st be installed in accordance
w
ith
the latest revision of the applicable standards and
national codes. This refers also to the electric, gas
and venting installation. Note: Additional standards
for installations in p
u
blic garages, aircraft hangars,
etc. may be applicable.
See Page 8, Section 5
.
CAUTION
Product Damage Hazard
Do not use equipment in area containing
corrosive chemicals.
Refer to appropriate Material Safety Data
Sheets (MSDS).
Failure to follow these instructions can result
in product damage.
Summary of Contents for Combat UHD-Series
