CRV-S
ERIES
I
NSTALLATION
, O
PERATION
AND
S
ERVICE
M
ANUAL
4 of 83
SECTION 2: INSTALLER RESPONSIBILITY
The installer is responsible for the follo
w
ing:
• To ens
u
re the system is designed in accordance
w
ith the parameters of the CRV-Series
Design
Man
u
al (P/N 127500NA).
• To install the heater, as
w
ell as the gas and
electrical s
u
pplies, in accordance
w
ith applicable
specifications and codes. Roberts-Gordon LLC
recommends the installer contact a local B
u
ilding
Inspector or Fire Marshal for g
u
idance.
• To
u
se the information gi
v
en in a layo
u
t dra
w
ing
and in the man
u
al together
w
ith the cited codes
and reg
u
lations to perform the installation.
• To install the heater in accordance
w
ith the
clearances to comb
u
stibles req
u
irements.
• To f
u
rnish all needed materials not f
u
rnished as
standard eq
u
ipment.
• To plan location of s
u
pports.
• To pro
v
ide access to b
u
rners on all sides for
ser
v
icing or b
u
rner remo
v
al.
• To pro
v
ide the o
w
ner
w
ith a copy of this
Installation, Operation and Ser
v
ice Man
u
al.
• To ne
v
er
u
se heater as a s
u
pport for ladder or
other access eq
u
ipment and to ne
v
er hang or
s
u
spend anything from heater.
• To ens
u
re there is adeq
u
ate air circ
u
lation aro
u
nd
the heater and to s
u
pply air for comb
u
stion,
v
entilation and distrib
u
tion in accordance
w
ith
local codes.
• To safely and adeq
u
ately install heater
u
sing
materials
w
ith a minimal
w
orking load of 75 lb
(33 kg).
• To ens
u
re the heater is placed in an appro
v
ed
application.
2.1 Wall Ta
g
A laminated
w
all tag is a
v
ailable for the heater as a
permanent reminder of the safety instr
u
ctions and
the importance of the req
u
ired clearances to
comb
u
stibles. Please contact Roberts-Gordon LLC
or yo
u
r ROBERTS GORDON
®
independent
distrib
u
tor to obtain the
w
all tag. Affix the tag by
peeling off the backing of the adhesi
v
e strips on the
rear s
u
rface and position the tag on a
w
all near the
CRV-Series heater (e.g. thermostat or controller).
A copy of the
w
all tag (P/N 91037912) is ill
u
strated on
the back co
v
er. For an immediate sol
u
tion, yo
u
may
affix this copy on the
w
all near the heater.
Kno
w
yo
u
r model n
u
mber and installed config
u
ration.
Model n
u
mber and installed config
u
ration are fo
u
nd
on the b
u
rner and in the Installation, Operation and
Ser
v
ice Man
u
al.
See Page 6, Figure 3
through Page
8, Figure 11
. Write the proper clearance dimensions
in permanent ink according to yo
u
r model n
u
mber
and config
u
ration in the open spaces on the tag.
2.2 Corrosive Chemicals
Roberts-Gordon LLC cannot be responsible for
ens
u
ring that all appropriate safety meas
u
res are
u
ndertaken prior to installation; this is entirely the
responsibility of the installer. It is essential that the
contractor, the s
u
b-contractor, or the o
w
ner identifies
the presence of comb
u
stible materials, corrosi
v
e
chemicals or halogenated hydrocarbons* any
w
here
in the premises.
* Halogenated Hydrocarbons
are a family of
chemical compounds characterized by the
presence of halogen elements (fluorine, chlorine,
bromine, etc.). These compounds are
frequently used in refrigerants, cleaning agents,
solvents, etc. If these compounds enter the air
supply of the burner, the life span of the heater
components will be greatly reduced. An outside air
supply must be provided to the burners whenever
the presence of these compounds is suspected.
Warranty will be invalid if the heater is exposed to
halogenated hydrocarbons.
2.3 National Standards and Applicable Codes
All appliances m
u
st be installed in accordance
w
ith
the latest re
v
ision of the applicable standards and
national codes. This refers also to the electric, gas
and
v
enting installation. Note: Additional standards
for installations in p
u
blic garages, aircraft hangars,
etc. may be applicable.
CAUTION
Product Damage Hazard
Do not use heater in area containing
corrosive chemicals.
Refer to appropriate Material Safety Data
Sheets (MSDS).
Failure to follow these instructions can result
in product damage.
Summary of Contents for CoRayVac CRV-B-10
