Robertshaw Paragon 9145 Manual Download | Manualshive

Page: 5 / 12

background image

5

Representative Wiring Installation Procedure Model 9045

Connecting the refrigeration / defrost equipment (See Figures 3 and 4)

NOTE: Rated input power 120/208-240V AC 50/60 Hz (+10,-15%)

1. Turn off the AC power.

2. Open the metal case to access the control connectors.

3. Connect the wires from the compressor to terminal A.

4. Connect the defrost device (heater or hot gas solenoid) to terminal E.

5. Connect the wire from L1 - 120V AC or 208-240V AC line - to terminal C.

6. Jumper terminal C to terminals B and D.

7. Connect the wire from L2/N to terminal F.

Fig. 3 Load / AC Input Connectors Terminal Block Model 9045

Fig. 4 Model 9045

A B C D E F G

«
...
3
4
5
6
7
...
»

Summary of Contents for Paragon 9145













Reviews:

No comments

Related manuals for Paragon 9145

Durant Eclipse Series

Brand: Eaton Pages: 23

Brand: Lumo Pages: 2

Brand: ABB Pages: 7

Brand: Chauvet Pages: 2

Brand: GEV Pages: 10

Brand: Koch Pages: 2

Brand: Prime Pages: 2

Brand: Prime Pages: 4

Brand: hager Pages: 2

Brand: hager Pages: 2

T 1030 plus 1860

Brand: Gardena Pages: 12

Brand: Eaton Pages: 4

Brand: Panasonic Pages: 16

Brand: IDEC Pages: 40

Brand: PAPILLON Pages: 3

Speed-Timer 3000

Brand: R.U. Ready Pages: 2

Brand: Tekmar Pages: 4

2000 Series Drive-Thru Timer System 2+2/386

Brand: Phase Research Pages: 131

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands