1
2
3
4
6
5
7
8
9
10
11
12
13
15
14
16
17
18
19
20
21
22
24
23
25
26
27
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or allow limitations on how long an implied
warranty lasts, so the above limitations or exclusions may not apply
to you. This Warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
For Warranty returns, send the thermostat, shipping prepaid and proof
of date of purchase to:
Invensys Controls
Warranty Claims Department
515 S. Promenade Ave.
Corona, CA 92879-1736
In Canada:
Invensys Controls
Warranty Claims Department
3505 Laird Rd. Unit #14
Mississauga, Ontario L5L 5Y7 Canada
TWO YEAR LIMITED WARRANTY
Invensys Controls warrants to the original contractor installer, or to the
original consumer user, that each new Robertshaw thermostat will be
free from defects in materials and workmanship under normal use
and service for a period of two (2) years from the date of purchase
(the “Warranty Period”). If any Product fails within the applicable War-
ranty Period, Invensys Controls shall, at its option, repair or replace the
Product or credit the purchase price, provided the Product is returned
to Invensys Controls’ facility or designated agent within the Warranty
Period, with transportation or postage charges prepaid and proof of
the date of purchase, and the Product, upon examination by Invensys
Controls, is found not to conform to the Warranty. Cost of Product
removal, labor, or reinstallation of new Product are not covered under
this Warranty and are not the responsibility of Invensys Controls. War-
ranty on Products, parts and/or components sold, but not manufac-
tured by Invensys Controls, shall be expressly limited to the warranty
terms of the manufacturer of such products, parts and/or components.
The above warranty does not apply to: i) batteries; ii) defects or dam-
age that result from use of the Products in any manner other than
their normal and customary manner; iii) defects or damage that result
from use of the Products in any manner other than in accordance with
Invensys Controls’ recommendations and instructions; iv) defects or
damage which occur from misuse, alteration, accident, water, fire or
neglect; and/or v) defects due to abuse or damage such as burned
contacts, stripped threads, split castings, improper installation or
missing parts.
THE FOREGOING WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER
WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY, TITLE AND
FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL
INVENSYS CONTROLS BE LIABLE TO CONSUMER, CONTRACTOR OR
ANY THIRD PARTY FOR ANY CONSEQUENTIAL, INCIDENTAL, SPECIAL,
EXEMPLARY, OR PUNITIVE DAMAGES ARISING FROM OR RELATING TO
USE OF THE PRODUCT INCLUDING, BUT NOT LIMITED TO, LOSS OF
GOODWILL, LOSS OF PROFIT OR REVENUE, AND PROPERTY DAMAGE,
REGARDLESS WHETHER SUCH LOSS OR DAMAGE IS BASED IN CON-
TRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY, INDEMNITY,
PRODUCT LIABILITY, OR OTHERWISE AND EVEN IF INVENSYS CON-
TROLS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REPAIR, REPLACEMENT, OR CREDIT OF THE PURCHASE PRICE, AS
PROVIDED HEREIN, SHALL CONSTITUTE THE SOLE REMEDIES WITH
RESPECT TO DEFECTS IN THE PRODUCTS. THE CONSUMER ASSUMES
ALL RISKS AND LIABILITY FOR INCIDENTAL AND CONSEQUENTIAL
DAMAGE RESULTING FROM INSTALLATION AND USE OF THE THERMO-
STAT.
TROUBLESHOOTING
Problem
Solution
Scrambled or double
display (numbers over
numbers).
Remove clear mylar sticker.
No display.
Check connections and batteries.
Press Reset once with a small pin and
hold for two seconds then reprogram.
Entire display dims.
Replace batteries.
Auto/Fan does not turn
On.
There may be as much as four minute
delay before the heat or cool system
turns on. Wait and check. (Compressor
protection delay).
Check your circuit breakers and switches
to ensure there is power to the system.
Replace batteries.
Make sure your furnace blower door is
closed properly.
Check the position of the furnace or Heat
Pump selector switches.
Erratic display.
Press
RESET
once with a small pin and
hold for two seconds then reprogram.
Thermostat reads E1.
Temperature sensor defective. Replace
unit.
Thermostat reads E2.
System switch in wrong position. Move
system switch to correct position.
If you experience any other problems, contact Technical Support at:
www.invensyscontrols.com or (800) 445-8299.
INSTALLATION MANUAL
The information supplied here is for the mounting, wiring and switch
set up for the RS2110C and RS2210C thermostats. For programming
and operating functions, refer to the User Manual section.
Thank you for selecting our wall thermostat. Robertshaw
®
products are
manufactured to high quality standards and are designed to provide
years of service.
The RS2110C and RS2210C thermostats work with the following
climate control configurations:
• Heat Pump (No Auxiliary Heat)
• Heat Pump (With Auxiliary/Emergency Heat)
• Standard Heat and Cooling Systems
• One Stage Heat/Cool - RS2110C
• Two Stage Heat, One Stage Cool - RS2210C
• Standard Heat Only Systems
• Millivolt Heat Only Systems - Floor or Wall Furnaces
• Standard Central Air Conditioning
• Gas or Oil Heat
• Electric Furnace
• Hydronic (Hot Water) Zone Heat-2 Wires
• Not to be Used With Split Transformer Systems
The RS2110C and RS2210C thermostats will NOT work with 3-Wire
Hydronic (Hot Water) Zone Heat 110/220 Volts. This thermostat operates
on 24 VAC power or battery power.
IMPORTANT SAFETY INFORMATION
WARNING:
Electrical Shock Hazard
Turn off power at the main power source by unscrewing
the fuse or switching the circuit breaker to the
OFF
position before installing, removing or cleaning this
thermostat.
Fire and Electrical Shock Hazard
This device should be installed by a qualified service
technician with due regard for safety as improper
installation could result in a fire and electrical shock
hazard.
Fire and Electrical Shock Hazard
This is a 24 VAC low-voltage thermostat. Do not install on
voltages higher than 30 VAC.
• Do not switch system to
COOL
if the temperature is below 50ºF
(10ºC). This can damage your cooling system and may cause
personal injury.
• Do not short (jumper) across terminals on the gas valve or at the
system control to test installation. This will damage the thermostat
and void the warranty.
• Do not connect ground to any terminal in this unit.
• All wiring must conform to local and national building and
electrical codes and ordinances.
• Use this thermostat only as described in this manual.
CAUTION:
• Read all the information in this manual before installing this
thermostat.
• This thermostat is equipped with automatic compressor protection
to prevent damage due to short cycling or extended power
outages. The short cycle protection provides a 4 minute delay
between heating or cooling cycles to prevent the compressor from
being damaged.
• The batteries must be replaced at least every 18-24 months to
assure proper operation. The thermostat will display a flashing low
battery when it is time to replace the batteries. The manufacturer
recommends inserting fresh batteries before leaving for an
extended period.
Recycling Thermostat
This thermostat does not contain mercury. However, if this thermostat
is replacing a thermostat that contains mercury in a sealed tube, do
not place your old thermostat in the garbage. Contact your local waste
management authority for instructions regarding proper disposal of
the thermostat. If you have any questions, call Robertshaw technical
support at 1-800-445-8299.
MOUNTING
What you need:
This thermostat includes two #8 slotted screws and two wall anchors
for mounting. To install your thermostat, you should have the following
tools and materials.
• Slotted Screwdriver(s)
• Small Phillips Screwdriver
• Hammer
• Electric Drill and 3/16" Bit
• Two 1.5V (AA) Alkaline
Batteries (included)
Replacing Existing Thermostat
WARNING:
Electrical Shock Hazard
Turn off power at the main power source by unscrewing
the fuse or switching the circuit breaker to the
OFF
position before installing, removing or cleaning this
thermostat.
IMPORTANT:
• Before removing wires from old thermostat, label each wire with
the terminal designation it was removed from.
• Do not install on voltages greater than 30 VAC.
• Do not install on outside walls or in direct sunlight.
1. Shut off electricity at the main fuse box until installation is
complete. Ensure that electrical power is disconnected.
2. Remove old thermostat: A standard heat/cool thermostat
consists of three basic parts:
a. The cover - may be either a snap-on or hinge type.
b. The base - remove by loosening all screws.
c. The switching subbase or adapter plate - remove by
unscrewing the mounting screws that hold it on the wall.
3. Remove the front cover of the old thermostat. With wires still
attached, remove wallplate from the wall. If the old thermostat
has a wall mounting plate, remove the thermostat and the wall
mounting plate as an assembly.
4. Identify each wire attached to the old thermostat.
5. Label each wire to identify which terminal it was connected to.
6. Disconnect the wires from the old thermostat one at a time. DO
NOT LET WIRES FALL BACK INTO THE WALL.
7. Install new thermostat using the following procedures.
WARNING:
Do not use on circuits exceeding specified voltage. Higher
voltage will damage the control and could cause an
electrical shock or fire hazard. Do not short out terminals
on gas valve or primary control to test.
Incorrect wiring will damage the thermostat and could
cause personal injury and/or property damage.
Attach Thermostat Base to Wall
1. Remove the packing material from the thermostat. Push in on
the tab at the bottom. Gently pull the cover straight off the base.
Forcing or prying on the thermostat will cause damage to the
unit.
CAUTION:
Be certain all power is off to the system.
2. Pull the wires through the hole in the base. Connect wires
beneath terminal screws on base using the table under terminal
connections.
3. Place base over the hole in wall and mark mounting hole
locations on wall using the base as a template.
4. Move the base out of the way. Drill mounting holes.
5. Fasten base loosely to wall, using two mounting screws. Place a
level against bottom of base, adjust until level, and then tighten
screws. Leveling is for appearance only and will not affect
thermostat operation. If you are using existing mounting holes,
or if holes drilled are too large and do not allow you to tighten
base snugly, use plastic screw anchors to secure the subbase.
6. Push excess wire into wall and plug hole with a fire resistant
material (such as fiberglass insulation) to prevent drafts from
affecting thermostat operation.
Mounting Holes
Terminals
Figure 1 Thermostat Base
System Switch Selection
STD
HP
GAS
ELEC
Heat Pump or Non-Heat Pump (RS2110C only)
Gas or Electric
Figure 2 Electric/Gas Switch (Fan Option)
The RS2110C thermostat is configured from the factory to operate a
heat/cool, fossil fuel (gas, oil, etc.), forced air system. It is configured
correctly for any system that DOES NOT require the thermostat to
energize the fan on a call for heat.
The RS2210C is configured at the factory to operate an electric
heat or heat-pump system that requires the thermostat to turn on
the fan on a call for heat. Locate the
ELEC
/
GAS
switch on the back
of the thermostat (see “Figure 2 Electric/Gas Switch (Fan Option)”)
and switch it to the
ELEC
position. This will allow the thermostat to
energize the fan immediately on a call for heat.
Press the reset button to accept a change in the switch option.
If your system is not a heat pump system, refer to the Configuration
section in this manual. The RS2210C thermostat must be changed to
a
STD
type system.
If you are unsure if the heating/cooling system requires the thermo-
stat to control the fan, contact a qualified heating and air conditioning
service person.
When the thermostat is configured for heat pump, the thermostat will
always power the circulator fan on a call for heat in the Heat mode.
The
ELEC
/
GAS
switch for the 2 stage RS2210C model must be set to
match the type of auxiliary heat your system uses for proper operation
in the Emergency mode.
All wiring diagrams are for typical systems only. Refer to equipment
manufacturer’s instructions for specific system wiring information.
Thermostat Terminals
Terminal
Equipment to
Connect
Description
One Stage Model RS2110C
C
24 VAC common
connection
For input of 24 VAC common side of
transformer.
If 24 VAC is not pres-
ent the thermostat is powered by
batteries only and THE SYSTEM
WILL NOT OPERATE.
R
24 VAC + con-
nection
For input of 24 VAC hot side of
transformer runs heating and cooling
system.
O
Energizes for heat pump cool revers-
ing valve.
B
Energizes for heat pump heat revers-
ing valve.
G
Indoor fan con-
nection
Energizes with Y1 and Y2.
Energizes with W1 and W2 if the
ELEC
/
GAS
switch is set to electric.
Energizes when fan is switched to
ON
.
Y1*
First stage
compressor con-
nection
Energizes on a call for first stage of
cooling.
Energizes on a call for first stage of
heating when configured as a
HP
.
E/W1*
First stage heat/
emergency heat
connection
Energizes on a call for first stage
of heating when configured as a
Non-Heat Pump. For Heat Pump
configuration, will energize for emer-
gency heat.
*This thermostat can be used as a heat only or cool only thermostat.
Therefore, it is not always necessary to use both W1 and Y1.
Terminal
Equipment to
Connect
Description
Two Stage Model RS2210C (Additional Terminals)
W2
Second stage
heat connection
Energizes on a call for second stage
heating.
L
24 VAC com-
pressor fault
output
For input of fault signal from a
compressor.
Replace the cover by inserting the bottom tab on the thermostat body
into the slot at the bottom of the wallplate. Move the cover to meet
the top of the wallplate. Press the top of the body to snap it into the
wallplate.
CAUTION:
Do not force the thermostat body onto the wallplate. Termi-
nal pins inside the thermostat may become damaged.
WIRING DIAGRAMS
Heat Pump Terminal Outputs
Refer to the equipment manufacturer’s instructions for specific system
wiring information. You can configure the thermostat for use with a
Heat Pump Type 1, single stage compressor system. This thermostat
is designed to operate a single transformer system. If you have a two
transformer system, cut and tape off one transformer. If transformer
safety circuits are in only one of the systems, remove the transformer
of the system with no safety circuits. If required, replace the remain-
ing transformer with a 75 VA Class II transformer. After disconnecting
one transformer, the two commons must be jumpered together.
Use the terminal output information below to help you wire the ther-
mostat properly for your system.
Single Stage Heat and Cool: RS2110C
A. Typical wiring diagram for single transformer standard system.
System selector switch must be set to
STD
.
NOTE:
“Battery Operation Only” if 24 VAC common not present, other-
wise “Battery Backup”.
C R O B G Y1 W1
24 VAC Common
(Battery Operation
Only if not present)
24 VAC
Supply
Fan Relay
Compressor
Contactor
First Stage
Heat
B. Typical wiring diagram for single transformer heat pump system.
System selector switch must be set to
HP
.
NOTE:
“Battery Operation Only” if 24 VAC common not present, other-
wise “Battery Backup”.
C R O B G Y1 W1
24 VAC
Common
(Battery
Operation
Only if not
present)
24 VAC
Supply
Fan Relay
Compressor
Contactor
Cool Active
Reversing
Valve
Heat Active
Reversing
Valve
Two Stage Heat Single Stage Cool: RS2210C
C. Wiring diagram for single transformer standard system. System
selector in configuration menu must be set to
STD2
or
STD1
(single stage only).
NOTE:
“Battery Operation Only” if 24 VAC common not present, other-
wise “Battery Backup”.
C R O B G Y1 E/W1
24 VAC
Common
(Battery
Operation
Only if not
present)
24 VAC
Supply
Fan Relay
Compressor
Contactor
L
W2
First Stage
Heat
Second Stage
Heat (if STD2
selected)
D. Wiring diagram for single transformer heat pump system. System
selector in configuration menu must be set to
HP
.
NOTE:
“Battery Operation Only” if 24 VAC common not present, other-
wise “Battery Backup”.
C R O B G Y1 E/W1
24 VAC
Common
(Battery
Operation
Only if not
present)
24 VAC
Supply
Fan Relay
Compressor
Contactor
Cool Active
Reversing
Valve
Heat Active
Reversing
Valve
L
W2
Compressor
Fault Output
(24 VAC) from
Heat Pump
Emergency
Heat
Second
Stage or
Auxiliary Heat
E. Typical wiring diagram for single transformer heat pump systems.
24 VAC
Supply
R
Y1
Compressor
Contactor
O
Reversing
Valve
Energized
in Cool
Mode
B
Reversing
Valve
Energized in
Heat, Off,
Emergency
Mode
24 VAC
120
VAC
Neutral
Hot
Transformer (Class II Current Limited)
C
24 VAC
Common
(Battery
Operation
Only if not
present)
System
Monitor
Switch
L
=
Compressor
Fault Output
(24 VAC) from
Heat Pump
Auxiliary
Heat Relay
Emergency
Heat Relay
G
Fan Relay
E/W1 W2
F. Typical wiring diagram for single transformer heat pump only.
R
G
Fan Relay
Y1
O
Reversing
Valve Ener-
gized in Cool
Mode
B
Reversing Valve
Energized in
Heat, Off,
Emergency
Mode
24 VAC
120
VAC
Neutral
Hot
Transformer (Class II Current Limited)
C
Compressor
Contactor
Stage 1
Emergency
Heat
Heat Relay
Stage 2
Compressor
Fault Output
(24 VAC) from
Heat Pump
E/W1 W2 L
Battery Compartment
- Open with finger from sides. Install two AA
1.5V batteries.
Reset Button
- Press to return to factory default.
Door Latch
- Press gently on door to open/close.
System Switch
- Select Cool/Off/Heat.
Fan Switch
- Set for continuous or automatic fan operation.
IMPORTANT:
Please read the entire User Manual section before set-
ting your thermostat.
DISPLAY MAP
The thermostat display will show information that is being used during
operation or programming. This illustration shows all of the display’s
possibilities with an explanation.
1
2
3
4
5
6
Figure 5
1. Used with setpoint.
2. Used for service reminders (e.g. CHECK HP).
3. Used for current setpoint and some configuration data.
4. HVAC mode and status. Icons blink when active. A is for Auto, 2
is for second stage and E is for emergency.
5. Low battery indicator.
6. Used for ambient temperature and configuration data (e.g. first
stage differential, F or C, etc.).
COMPRESSOR PROTECTION
The thermostat provides a 4 minute delay after shutting off the
heating or cooling system before it can be restarted. This feature will
prevent damage to your compressor caused by rapid cycling. Note
that this delay also applies to the heating system control. It does not
provide a delay when there are power outages.
TEMPERATURE RANGE
This thermostat can be set between 45ºF and 90ºF (7ºC and 32ºC).
However, it will display room temperatures from 30ºF to 99ºF (0ºC and
37ºC).
NOTE:
If the thermostat measures a temperature over 99ºF (37ºC), HI
will be displayed on the LCD. If the temperature is below 32ºF
(0ºC), LO will be displayed on the LCD.
AUTO CUT-OFF
Your thermostat will automatically shut down in Heat mode if the room
temperature rises above 95ºF (35ºC). It will shut down in Cool mode if
the room temperature drops below 45ºF (7ºC).
Note that if your system has malfunctioned and no longer responds to
thermostat controls, the Auto Cut-Off will not work.
EMERGENCY HEAT - RS2210C WITH HEAT PUMP
Consult with your installer to determine if your system is a heat pump
with an emergency heat system installed. If you have an emergency
heat system you can activate it in
HEAT
mode by pressing the
UP
and
DOWN
arrows together. The display will show an
E
by the flame icon
when the thermostat is in system
HEAT
mode.
The main heating system will not receive a call to turn on. This will
allow maintenance to take place on the main heat system. To turn off
the emergency system, press the
UP
and
DOWN
arrows together. The
E
will no longer be displayed.
POWER FAILURE
Whenever the main power is interrupted or fails, the back-up battery
power will maintain the current settings. The heating and cooling
systems will not function. In the event of a power outage and dead
batteries, the settings will revert to default settings when power is
resumed. You must reprogram your settings.
FILTER MONITOR
The thermostat counts the number of hours your system’s filter has
been in use. To maximize your system’s performance and energy
efficiency, change or clean your filter regularly. When the total system
run time for heat and cool reaches 400 hours, the filter change indica-
tor (
Check FLtr
) will flash as a reminder to check your system’s filter.
Press and hold the
UP
and
DOWN
arrows together until C
heck FLtr
no
longer displays. This will reset the filter monitor to zero.
BATTERY WARNING
+
- +
-
Figure 6
When the batteries become weak, a flashing battery symbol will
appear on the screen. When this symbol occurs, install two new AA
batteries. You have approximately one minute to change the batteries
and keep the thermostat’s program settings. Once the batteries have
become too weak to ensure proper operation, your system will be
turned off, and the display will be blank if battery powered.
CAUTION:
When the battery symbol flashes the batteries are weak. If
they are not replaced the display will fade. When the bat-
teries are dead the display will be blank. There will be no
temperature control and settings are not saved.
NOTE:
If you plan to be away from the premises over 30 days, we
recommend that you replace the old batteries with new alka-
line batteries prior to leaving.
CONFIGURATION
The
RESET
button can be pressed with a paper clip to reset the
thermostat back to the factory defaults as shown in the Configuration
Menu Options table.
The Configuration Menu allows you to set certain thermostat operating
characteristics for your system or personal requirements. Set System
switch to
OFF
, then simultaneously press the
UP
and
DOWN
arrows
for three seconds to enter the Configuration Menu which summarizes
the options available. The display will show the first item in the Con-
figuration Menu Options table. An explanation of each option is listed
after the table. Press the
DOWN
arrow to change to the next menu
item. To change the setting, press the
UP
arrow. When the maximum
setting is reached, the selections will return to the lowest selection. To
exit the menu and return to the program operation, press the
DOWN
arrow until the main display appears. If no buttons are pressed within
fifteen seconds, the thermostat will revert to normal operation.
Configuration Menu Options
Item
Default
Temperature Scale F/C
F
First Stage Differential
1°F (0.5°C)
RS2210C only - Second Stage Differential
2°F (1.1°C)
Off Set
0
RS2210C only - DLY 2
20
RS2210C only - System Type
HP
Temperature Scale - Select Fahrenheit or Celsius.
First Stage Differential - When the room temperature approaches the
set temperature the differential is the amount of overshoot allowed
before the thermostat calls for heating/cooling.
Second Stage Differential - Used for RS2210C only, same as First
Stage Differential but controls a second stage system.
Offset - Use this to change ambient temperature readings up or down.
DLY2 - Used for RS2210C only, is the second stage delay time.
HP - Used for selecting the system type on the RS2210C. Select
HP
for heat pump. Select
STD1
for one stage heating non-heat pump.
Select
STD2
for two stage heating non-heat pump.
Familiarize yourself with these manual settings, so that you can easily
modify your settings as your comfort needs change. The example
below demonstrates the manual settings method.
NOTE:
The temperature can be set in increments of 1ºF (1ºC).The heat
setpoint cannot be set higher than the cool setpoint, and the
cool setpoint cannot be set lower than the heat setpoint. If the
system selector is in Heat mode, the heat operating mode will
be set. After 15 seconds without a button press, the thermo-
stat will return to Normal Display mode.
Changing Settings
Start with a normal running display.
1. Select Heating with the system switch.
2. Use the
UP
and
DOWN
arrows to select the temperature for
heating.
3. Switch between
HEAT
and
COOL
. Repeat step 2 to select the
temperature for cooling.
OPERATION
System Selector Switch
system
cool off heat
The System Selector switch on the front of the
thermostat determines the operating mode of the
thermostat. You may select
COOL
,
OFF
, or
HEAT
.
NOTE:
Anytime you install or remove the thermostat
from the wallplate, slide the System Selector to the
OFF
posi-
tion to prevent the possibility of a rapid system on-off.
Fan Switch
fan
on
auto
The Fan switch should normally be set in the
AUTO
position. The fan will be turned on along with normal
operation of your system. In a normal gas or oil
furnace, the fan will be turned on by your furnace
after its warm-up delay. For electric heat, air
conditioning, and heat pump operation, the fan will turn on with the
system. To run the fan continuously, slide the Fan switch to the
ON
position.
INSTALL BATTERIES
The thermostat will operate using 24 VAC or two AA batteries. When the
two AA batteries are installed the thermostat will continue to run if the
24 VAC fails.
To open the door to the battery compartment, gently pull down on the
sides. Install two AA batteries following the polarity as shown inside the
compartment. Close the door.
+
- +
-
Figure 3
When the batteries are low the thermostat will enter a low battery
mode.
Low battery mode has two levels:
• Level 1 - The low battery icon will be
displayed. The thermostat will continue to
operate. Replace the batteries as soon as
possible.
• Level 2 - The low battery icon will flash. If 24
VAC is present the thermostat will continue
to operate if the batteries are discharged
or removed. If 24 VAC is not present the
thermostat is powered by batteries only and
THE SYSTEM WILL NOT OPERATE. Replace
batteries immediately.
Replace batteries if leaving thermostat unattended for more than
30 days.
CHECK THERMOSTAT OPERATION
Fan Operation
If your system does not have a G terminal connection, skip to Heating
System.
1. Turn on power to system.
2. Move Fan switch to
ON
position. The blower should begin to
operate.
3. Move Fan switch to
AUTO
position. The blower should stop
immediately.
Heating System
1. Move System switch to
HEAT
mode. If the heating system has a
standing pilot, be sure to light it.
2. Press the
UP
arrow to adjust thermostat setting to 1˚F/1˚C above
room temperature. The heating system should begin to operate.
The display should show the flame icon in motion.
3. For a RS2210C system, adjust temperature setting to 3˚F/3˚C
above room temperature. If your system configuration is set for
auxiliary heat, the auxiliary heat system should begin to operate.
A 2 will appear by the flame icon.
4. Press the
DOWN
arrow to adjust the thermostat below room
temperature. The heating system should stop operating.
Cooling System
1. Move System switch to select the
COOL
mode.
2. Press the
DOWN
arrow to adjust thermostat setting below room
temperature. The blower should come on immediately on high
speed, followed by cold air circulation. The display should show
the snowflake icon pulsing.
3. Press the
UP
arrow to adjust the temperature setting above
room temperature. The cooling system should stop operating.
If these tests are not successful, remove the thermostat body and
check for bent pins. Check all wiring connections.
If these tests are successful the thermostat is ready to operate using
the factory defaults. To change the configuration settings, refer to
Configuration in the User Manual section.
Installation of the thermostat is now complete. Remove the protec-
tive mylar over the screen and check that fresh batteries are properly
installed. Close all doors.
USER MANUAL
Thank you for selecting our wall thermostat. Robertshaw
®
products
are manufactured to high quality standards and are designed to
provide years of service.
FEATURES AND BENEFITS
• Multi-Stage 2 Heat/1 Cool - RS2210C only. Operates on both
multi-stage gas/electric furnaces and heat pumps.
• New Improved Display makes viewing and setting the temperature
easier.
• Adjustable Temperature Differential maintains optimal customer
comfort.
• Worry-Free Memory Retention - RS2210C only. Maintains set point
and programmed parameters, even during power outages.
• Filter Monitor provides notice when filters need changing.
• Automatic Compressor Short Cycle Protection reduces wear and
tear of HVAC equipment with this system safeguard.
• O and B Terminals provides greater system flexibility.
• Zone System Compatible acts as a sensor within the system.
• Quick Wire Terminal Block uses sturdy wire clamps for fast and
easy installation - no wrapping around screws.
This section will describe the features and how to set up the RS2110C
and RS2210C thermostats. Installation is described in detail in the
Installation Manual section.
+
- +
-
LCD Display
Down and
Up Arrows
Battery
Compartment
Door Latch
System Switch
Fan Switch
Reset Button
Figure 4
LCD Display
- Shows Day, Temperature and other feature information.
Down and Up Arrows
- Used to enter and navigate the configuration
menu and change the temperature settings.
352-00021-011 Rev B
191 E. North Avenue
Carol Stream, Illinois 60188 USA
www.invensyscontrols.com
©2012 Invensys Controls 7/12
352-00021-011 Rev B
Digital Non-Programmable Thermostat
Installation and User Manual
Model: RS2110C and RS2210C Series
