background image

 

 

Safety Warnings

 

 

Important: 

Please read the entire instructions before installing the rangehood. Check appliance for damage or missing 
parts (if damaged, do not install). 

This appliance is not intended for use by persons (including children) with reduced physical, sensory or 
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or 
instruction concerning use of the appliance by a person responsible for their safety. 

Young children should be supervised to ensure that they do not play with the appliance. 

This rangehood is designed for indoor use only and must be in a dry location.

 

Always switch power off prior to installation. 

All electrical work must be done by a registered electrician in accordance with local and national  
electrical codes as applicable. For your safety, this product must be earthed. 

A power outlet should be within 1m of the power cord exit from the rangehood. 
The socket must be accessible and enable the end user to isolate the rangehood from the power for the 
purpose of internal cleaning or maintenance. 

Disconnect the power supply when any maintenance is carried out, including changing light bulbs or 
inspecting filters. Do not touch lights after appliance use. 

Exhaust air must not be discharged into an existing flue which is used for exhausting fumes from 
appliances burning gas or other fuels. 

The minimum distance between an electric or gas hob surface and the lowest part of the rangehood is 
650mm.  If the instructions for the hob specify a greater distance, this has to be taken into account. 
Regulations concerning the discharge of air have to be fulfilled.

 

Stainless steel or powder coat is very easily damaged during installation if abraded or knocked by tools.  
Protect the rangehood with the cardboard box or plastic bag during installation. 
All ducting must comply with local requirements and building codes. 
Suitable fixings will be required to mount this rangehood. 

There shall be adequate ventilation of the room when the rangehood is used at the same time as appliances 
burning gas or other fuels

  

           900mm rangehoods are for 900mm hobs. 

Stainless steel is very easily damaged during installation if abraded or knocked by tools.  Protect the 

rangehood with the cardboard box or plastic bag during installation. 

See Ducting options next page. 

 

CAUTION: Accessible parts may become hot when used with cooking appliances. 

WARNING: Failure to install the screws or fixing devices in accordance with these instructions may 
result in an electrical hazard. 

It is recommended that the rangehood is started before cooking, and allowed to run for a period after 
cooking has finished (to remove vapours & odours).

 Turn off when not in use. 

There is a fire risk if cleaning is not carried out in accordance with the instruction. 

You must read the 

details concerning the method and frequency of cleaning. 

Do not flambé under the rangehood. 

 

 
 
 

 
 

 
 
 
 
 
 
 
 

 

 

Summary of Contents for RIJ3CL9BK













Reviews: