background image

30

6. 

Robomow Operation

6.1 

Automatic Operation

 As a part of the One-Time Setup, you have defined the area of your lawn. Based on this setting, Robomow 

will automatically derive the required number of mowing hours for your lawn (Mowing Cycle).

 Once the One-Time Setup is finished, Robomow will be set to perform automatically the following cycle of 

mowing operations:

 When the battery is fully charged, Robomow will automatically depart from the Base Station.

It will mow the lawn.

It will start searching for the Base Station, when the battery level gets low (Robomow will not mow when 

it is searching for the Base Station). 

It will recharge the battery and get ready for the next scheduled operation.

It will continue mowing until it completes the required number of mowing hours (end of a Mowing Cycle).

Note:

 Robomow mows the Edge only on the first mowing operation of each Mowing Cycle. In the rest of 

operations Robomow mows the lawn without the Edge. When Mowing Frequency (p001 in Section 6.4.2) is 

set to HIGH, Robomow will mow the Edge twice a week.

 Robomow stays in the Base Station during the default 

Inactive Time

 (All day Sunday and nighttime daily 

23:00 to 06:00). Inactive Time may be changed – see Section 6.4.1.3.

The required mowing time is automatically derived from the 

Area

 setting.

The mowing time may be adjusted using the 

Mowing Hours (%)

 menu – see Section 6.4.1.2.

 Robomow mows the entire area (i.e. starts a new Mowing Cycle) twice a week by default. This corresponds 

to a medium Mowing Frequency, which can be changed using the 

Mowing Frequency

 menu – see Section 

6.4.2 (p001 in the table).

Note!

Robomow has the power to mow high grass. However when mowing high grass during the first use or the first 

mowing of the season, initially you will see uneven patches of grass.
Please be patient as it may take a few days to one week to overcome and bring the lawn to an even height and 

consistency.

6.2 

Operating Panel

Operating Panel and buttons:

AM

Mo Tu We Th

Fr

Sa Su

Days of the week

Mower is in the 

Base Station 

indicator

Day and Time 

setting indicator

Mowing Hours (%) 

setting indicator

Inactive Time 

setting indicator

Rain Sensor

Red lit constantly – Low Battery

Green blinking – Charging

Green lit constantly – Fully Charged

Battery and 

Charging 

indicator

User / Error messages

Area setting indicator

Summary of Contents for MC1000





















































Reviews: