34
Screen
Setting
Description
Options
P003
Near Wire Follow
(Default =
ON
)
•
When Robomow completes its operation, or when the ‘Home’ button
instructs it to Go To Base, it drives itself to the Base Station.
•
Robomow drives along the Perimeter Wire with a dynamic offset (not
centered) to prevent wheel tracks along the same path. This return
behavior can be turned off.
On/OFF
P004
Max Near Wire
Follow Distance
(Default =
changed based on
the lawn area)
•
The maximum distance Robomow will drive from wire when returning
to the Base Station.
•
The distance does not represent actual units of measurement.
•
The offset Distance values range from 1 to 12. They represent
different distances from the wire.
•
The higher the Distance setting, the smaller the probability of tracks
along the perimeter.
•
Perimeter Islands that are relatively close to the Perimeter Wire or
narrow passages may prevent the mower to complete its drive to the
Base Station with ‘Near Wire Follow’ mode. In such cases decrease
the distance to allow the mower to complete the drive to the Base
Station.
1-12
P005
Min Near Wire
Follow Distance
(Default =
1
)
•
The minimum distance Robomow will drive from wire when returning
to the Base Station.
•
The larger the number, the bigger the distance the mower will drive
from the wire while returns to the Base Station.
1-5
P006
Near Wire Follow
Test
•
Enables to test the mower in the max ‘Near wire Follow Distance’
that is defined in menu P004.
•
If the mower is not able to complete the drive in ‘Near Wire’ mode
smoothly, then it is recommended to reduce the max distance set in
menu P004.
P007
Rain Sensor
(Default =
On
)
•
The Rain Sensor feature halts operation on rainy or highly humid
weather.
•
This is recommended for the health of the lawn. However, mowing
wet grass does not present any technical problem.
On/OFF
P008
Rain Sensor
Sensitivity
(Default =
25
)
•
Robomow detects rain when the current reading value is below the
set Sensitivity value and postpones operation.
•
The higher the Sensitivity setting, the more sensitive Robomow is to
rain detection.
0-30
P009
Edge On/Off
(Default =
ON
)
•
The Edge is a special mode, in which Robomow follows the perimeter
wire for complete and accurate owing of the lawn edges.
•
In lawns where the edge is not maintained well and the mover fails
to complete the drive along the edge of the lawn, it is recommended
to set the Edge to ‘Off’.
•
Setting the Edge to ‘Off’ disables the Edge mode in automatic
departures from the station, but still allows the Edge mowing when
pressing the ‘Edge’ mode button on the operating panel.
On/OFF
P010
Child Lock
(Default =
OFF
)
•
The Child Lock feature locks the buttons to prevent unintended
operation, especially by children.
•
If the Child Lock is set to ‘On’, to operate the mower it is required to
first press one of the operating mode buttons and then to press the
OK button to confirm.
On/OFF
P011
Anti-Theft /
Disabling Device
(Default =
OFF
)
•
The Anti-Theft / Disabling Device feature alarms the surroundings
in the event of an unintended use or removal of the mower from its
designated area.
•
To turn the Anti-Theft / Disabling Device On for the first time, set it to
‘On’ and choose a PIN code of 4 digits.
Tip
: Select a number you can remember. Write it down (bottom of
Chapter 10), and keep it in a safe place.
•
When the Anti-Theft / Disabling Device system is activated, 0000 will
be displayed. Enter your 4-digit code to deactivate the Anti-Theft /
Disabling Device.
•
If the code is not entered, then the message is changed to U062
(Alarm will soon be activated). Enter the code, otherwise the alarm
will start.
ON/OFF
1234
