background image

®

Blixer 5 and 

®

Blixer 6 Operation Manual

3

CAUTION:

Always connect the Robot Coupe to a grounded
outlet with Ground fault circuit interrupter (GFCI)
protection device.

Disconnect the machine from the power outlet
when not in use and when cleaning or servic-
ing the unit.

Machine must be operated and stored in a loca-
tion not subject to water drips or spray or ex-
plosive vapors.

The machine must not be modified in any way
from its original configuration.

Should the machine malfunction or should any
part be damaged, it must not be operated until
it is repaired by a qualified technician using only
genuine Robot Coupe® repair parts.

Operating times of 5 minutes or longer can
cause processed food to increase to tempera-
tures above 125 F.

Failure to follow operating instructions or at-
tempts to operate the machine outside its de-
sign limits may create a hazardous condition
that could damage the machine and /or injure
users.

The machine must be operated on a clean sturdy
counter or table.  Keep the area around and
under the machine clear to allow air circulation.
Otherwize, the motor can overheat.

I. INTRODUCTION

The Robot Coupe commercial food processor
performs a host of culinary feats.  It is specifically
designed for high speed and quality processing.  The
Robot Coupe also provides a wealth of safety and
operating features to make volume food preparation
a pleasure rather than a chore.

The operators manual is designed to guide the user
through the simple steps of use for a safe, long life
utilization.  The manual should be referred to any time
there is a question on operation. 

 THIS MANUAL

SHOULD BE KEPT WITHIN EASY ACCESS TO
ALL USERS FOR REFERENCE, AND SHOULD
BE READ COMPLETELY BY ALL FIRST TIME
USERS OF THE MACHINE.

CAUTION

:

 

Your Robot Coupe comes with a sharp

cutting blades.   Always handle with 

safety

 in mind.

WEAR CUT-RESISTANT GLOVES WHEN
HANDLING THE BLADES.

NOTICE

:  If the machine fails to operate as

described in this manual, or if the machine
malfunctions in any way, remove the machine from
use and have it serviced.  

DISCARD ALL FOOD

PROCESSED AT THE TIME OF THE
MALFUNCTION.

Machine specifications:

The 

Models 

®

Blixer 5 and 

®

Blixer 6

 are equipped

with a high speed motor generating 2 HP which plugs
into a standard 208/240 volt/60HZ power outlet.  The
full load amperage rating is 5.3 amps on low speed
and 5.8 amps on high speed.  The machines are
supplied with a stainless steel bowl:  the Blixer 5 with
a 5 1/2 quart and the Blixer 6 having a 7 quart bowl.
Both machines are supplied with S-blade and clear
polycarbonate cover.  A bowl and lid wiper assembly
is supplied with removable handle.

Summary of Contents for Blixer 5














Reviews: