background image

ROBOVENT • PFX SERIES OWNER’S MANUAL 

41

Teco Motor Greasing Guidelines

Lubrication Procedure

It is advisable to re-grease when the motor is running to allow the new grease to be evenly 
distributed inside the bearing. Before re-greasing, the inlet fitting should be thoroughly 
cleaned to prevent any accumulated dirt from being carried into the bearing with the new 
grease. The outlet of grease drainage should be opened to allow the proper venting of old 
grease. Use a grease gun to pump grease through grease nipple into the bearings. After re-
greasing, operate the motor for 10-30 minutes to allow any excess grease to vent out.

Approved Greases 

• 

All motors with ZZ bearings will have SHELL Alvania R3 (lithium base grease). 

• 

All motors with open bearings will have Polyrex EM (polyurea base grease).

• 

Certain T-frame models will utilize special grease and will be noted on the lubrication 

 nameplate.

Relubrication Time Interval & Amounts

*Fill new grease until it overflows and the old grease is entirely replaced.

BEARING SIZE 

MOTOR HP 

GREASE  

1800 RPM – 

3600 RPM –

 

 

AMOUNT 

HOUR CHANGE 

HOUR CHANGE

  

IN GRAMS 

INTERVAL 

INTERVAL

All motors listed are ODP
DE & NDE: 6306ZZ  

30 grams 

3000 hours 

2000 hours

DE & NDE: 6306ZZ  

7.5 

30 grams 

3000 hours 

2000 hours

DE: 6308ZZ  

10 

30 grams 

3000 hours 

2000 hours

DE: 6310ZZ  

20 

40 grams 

3000 hours 

2000 hours

DE: 6311ZZ & DE: 6212C3  

30 

40 grams 

3000 hours 

2000 hours

DE & NDE: 6213 & DE: 6212C3  

40 

50 grams 

3000 hours 

2000 hours

DE & NDE: 6213 & DE & NDE: 6213C3  

50 

50 grams 

3000 hours 

1000 hours

DE: 6314, NDE: 6213, DE: 6313C3 & NDE: 6213C3  

75 

80 grams 

3000 hours 

1000 hours

DE & NDE: 6317, DE: 6313C3 & NDE: 6213C3  

100 

120 grams 

2000 hours 

1000 hours

DE & NDE: 6317 & DE & NDE: 6313C3  

125 

120 grams 

2000 hours 

1000 hours

Relubrication Time Interval

SECTION 1000

Motor Greasing Guide

Summary of Contents for PFX Series





















































Reviews: