Hook Height and Winch Speed Monitoring RCI1550 Display Option
MAN-1111 Rev H
©Copyright 2014 LSI-Robway Pty Ltd
Page 186
CALIBRATION
NOTE: Calibration is performed through the function code menus in the DISRCI4100
Display. There are no user settable parameters in the DISRCI1550 Display.
Calibration MUST be performed in meters. The following function codes are used to calibrate hook height
for the main hoist rope and for the auxiliary hoist rope.
Typical Function Code Listing (numbers may vary by crane)
F-15 VIEW UNCALIBRATED MAIN HOOK HEIGHT INPUT
F-16 VIEW CALIBRATED MAIN HOOK HEIGHT INPUT
F-17 CALIBRATE MAIN HOOK HEIGHT
F-18 VIEW UNCALIBRATED AUX. HOOK HEIGHT INPUT
F-19 VIEW CALIBRATED AUX. HOOK HEIGHT INPUT
F-20 CALIBRATE AUX. HOOK HEIGHT
CALIBRATING MAIN HOOK HEIGHT
DO NOT LUFF BOOM DURING THIS PROCESS
Step 1)
Luff up to high boom angle where main and aux are over the crane deck. Select Main Winch
Step 2)
Place hook on crane deck, this will be zero height point.
Step 3)
Enter Function Code Menu
Step 4)
Scroll to F-17 using up/down arrows
Step 5)
Press Enter to set zero height automatically.
Step 6)
Display will prompt to hoist up to high hook. (“Hook Up” message)
Step 7)
Press Enter
Step 8)
Using up/down arrows set reading to actual hook height in meters above initial zero setting
Step 9)
Press Enter
Step 10)
The DISRCI1550 Display will now display Main hook height in meters.
CALIBRATING AUX HOOK HEIGHT
DO NOT LUFF BOOM DURING THIS PROCESS
Step 1)
Luff up to high boom angle where main and aux are over the crane deck.
Step 2)
Place hook on crane deck, this will be zero height point.
Step 3)
Enter Function Code Menu
Step 4)
Scroll to F-20 using up/down arrows
Step 5)
Press Enter to set zero height automatically
Step 6)
Display will prompt to hoist up to high hook. (“Hook Up” message)
Step 7)
Press Enter
Step 8)
Using up/down arrows set reading to actual hook height in meters above initial zero setting
Step 9)
Press Enter
Step 10)
The DISRCI1550 Display will now display Aux hook height in meters.
PERIODIC SYSTEM TESTING
•
There is no periodic testing required.
•
If the winch ropes are altered then the hook zero must be reset.
•
If the system is powered off and the crane is operated the hook height zero must be reset.
Summary of Contents for RCI-4100
