OPERATION AND INSTALLATION
RCI-4100 SYSTEM
MAN-1111 Rev H
©Copyright 2015 LSI-Robway Pty Ltd
Page 44
This Offset function code contains the factory default setting of the gain offset for the sensors. The
factory default settings are as follows and should be checked:
Recommended Gain and Offset settings:
1.5/3t Load Pin
Output:
Gain
Offset
1mV/V
790
37
Compression Cell
Output:
2mV/V
480
60
Angle Sensor
Type: Electronic
Gain
Offset
Output:
1.2 – 2.4VDC
730
255
NOTE: Correct Gain and Offset settings for the sensors on this crane can be found in the RCI
Configuration Sheet and Function Code List in Attachments.
6.9. Number of Sensor Samples to Average
This function is used to stabilise the display in the event that the numbers (readouts during normal
operating mode) are changing erratically. This value can be edited by using the Up/Down buttons.
Default setting is “0” and the maximum selectable value is “25”. It is recommended that this value is
set to “3” prior to performing calibration.
6.10. Load Chart View Mode
This function code can be used to view the load charts programmed in the software. It is not part of the
calibration or set-up procedures. It is mainly used by LSI-Robway for software checking.
6.11. View Digital Inputs
This function code is used to view the state (i.e. open or closed) of the eight digital (switch) inputs. The
inputs are used for wiring slew limit switches (or proximity switches), external duty selector, etc. to suit
specific application. This function is also useful during troubleshooting as the input switch status can
be viewed easily from the display unit in the cabin. The format is binary where input state 0 = On (low)
and input state 1 = Off (high). For example, “11110101” means that switch #5 and #7 are both “on”
and the rest are “off”.
6.12. Set Year
Use this function to set the current year.
6.13. Set Day and Month
Use this function to set the current day and month.
6.14. Set Time
Use this function to set the current time. The time displayed is in the format HH:MM. An invalid time
will cause an error message to appear.
6.15. Download Logger Contents to PC or SD Card
Please see Section 4 “Data Logging and Data Downloading” for details and procedure. Refer also to
APPENDIX F, Data Logging
Summary of Contents for RCI-4100
