OPERATION AND INSTALLATION
RCI-4100 SYSTEM
MAN-1111 Rev H
©Copyright 2015 LSI-Robway Pty Ltd
Page 49
7. Calibration
CAUTION: BEFORE ANY CALIBRATION FUNCTIONS CAN BE ACTIVATED, YOU MUST
ENTER CALIBRATION MODE.
CALIBRATION SHOULD ONLY BE CONDUCTED BY AUTHORISED
PERSONNEL.
RE-CALIBRATION NEED ONLY BE DONE AS A LAST RESORT AFTER
PERFORMING ALL OTHER SYSTEM TESTS.
7.1. Calibration Mode
The RCI-4100 sensors (load cells/pins, angle sensor etc.) require calibration (scaling) on the crane
so that their outputs accurately reflect crane parameters. All calibrations, as well as changes to any
settings (geometry, alarm thresholds etc.) are done using function codes when the display is in
calibration mode. Function codes can only be accessed when in calibration mode and are a
structured way of entering data into the processor for both LSI-Robway personnel and personnel in
the field. They are also used when data or settings need to viewed.
7.1.1.
Entering Calibration Mode
•
Ensure that the software number is correct for the crane and that the correct corresponding
software documents and GA (general arrangement - refer RCI System Configuration
Documents in Attachments) drawing is being used.
•
Ensure all duties (refer RCI System Configuration Documents in Attachments) match crane
load charts.
•
Make sure that the correct duty number (crane configuration, sea state) and falls (parts of line)
are selected,
•
Insert the over-ride key into the RCI-4100 Display and turn it on, make sure that the over-ride
indicator (O/R) is shown on the display,
•
Press and hold the SETUP button for about 2 seconds,
•
F-xx will be shown on the alphanumeric display, where xx is the last calibration function
performed or F-00 if this is the first time you entered calibration mode since last powering the
system,
7.1.2.
Using Calibration Functions
•
Once calibration mode is entered use the UP/DOWN keys to ramp through the calibration
functions.
•
When the correct function code is shown on the screen press the ENTER button to select
that function.
•
If the value is just being viewed and does not need to be changed, press CANCEL to
return to the function code number. Values will not be changed unless the ENTER key is
pressed.
•
If the value is to be changed, use the UP/DOWN keys to change the value and when the
value is correct press the ENTER button, note that the new value will be memorised at the
time that the ENTER button is pressed.
Summary of Contents for RCI-4100
