OPERATION AND INSTALLATION
RCI-4100 SYSTEM
MAN-1111 Rev H
©Copyright 2015 LSI-Robway Pty Ltd
Page 61
Error code 202:
This indicates that the signal from the auxiliary load sensor is too low or too high. This should be
confirmed by viewing the UNCALIBRATED TRANSDUCER 2 INPUT and noting that the value shown
in the LOAD display is lower than 50, or higher than 4050.
Possible causes:
•
Load cell signal wires shorted together.
•
The is shorted to the shield.
•
The excitation - is shorted to the shield.
•
The excitation supply is shorted together. This will obviously affect all of the external sensors.
Measure the excitation voltage and compare it with the expected value. If this is the cause,
the UNCALIBRATED value will generally be non-zero, but below 50.
•
The load cell is disconnected or there is an open circuit in one of the signal wires.
•
The signal - is connected to the shield.
•
The and the exci are swapped.
•
The signal - and the excitation - are swapped.
Error code 240:
This indicates that an overload has been detected. This error generally accompanies most other
errors simply because most other errors will place the display into an overload condition. This being
the case, you need to check what other errors are present and correct them first. Once these have
been addressed the E240 error generally takes care of itself. The exception is of course, when the
equipment has been put into a genuine overload situation which has not been caused by any external
faults.
Possible causes:
•
A genuine overload condition exists.
•
It has been caused by another error code condition.
Error code 280:
This indicates that the rated line-pull has been exceeded.
Possible causes:
•
A genuine line-pull error exists.
Error code 301:
This indicates that the angle being measured is outside of its allowed range.
Possible causes:
•
A genuine violation of the angle limits has occurred.
•
The angle sensor mounting may have loosened allowing the sensor to move.
•
Check the angle displayed against the actual angle of the boom.
Error code 304:
This indicates that the radius being measured is outside of its allowed range.
Possible causes:
•
A genuine violation of the radius limits has occurred.
•
Check as per Error code 301.
Error Code -999
This indicates an invalid calibration
Possible causes:
•
Low and high end of sensor calibrated to same raw counts.
Sensor needs to be re-calibrated to clear this error
Summary of Contents for RCI-4100
