OPERATION AND INSTALLATION
RCI-4100 SYSTEM
MAN-1111 Rev H
©Copyright 2015 LSI-Robway Pty Ltd
Page 72
9.1.6.
The approximate physical location on the plant of each item of electrical equipment to be
installed, and the proposed routing of any interconnecting cables. Where interconnecting
cables cross a zone boundary, care must be taken to ensure that such a crossing is
permitted, and if so, what additional requirements are placed on the cable installation. Refer
to the system overview drawing in the rear of the manual for component identification.
9.1.7.
Any cable identification detail. All cables containing Intrinsically Safe (IS) circuits must be
identified as such, either by a form of physical marking, or by the use of blue sheathing.
9.1.8.
Inspection check lists against which commissioning and routine inspections should be
carried out. Refer to the checklists on Section 9.4. “Inspection and Test Schedule”.
9.1.9.
Details of electrical testing required at commissioning and inspections. Should there be an
operational problem, there may be electrical testing required. Refer to the Trouble shooting
section.
9.1.10.
A record of any modifications and the justification for each modification. If such modifications
were present as supplied by LSI-Robway, then such a justification will accompany the
system. Where these modifications were performed by a party other than LSI-Robway,
these justifications must be supplied by those responsible for such modifications. LSI-
Robway takes no responsibility for modifications done to the system that have not been
authorised by LSI-Robway in written form.
9.1.11.
Details of any previous inspections. This generally will not be applicable, but is included for
the sake of completeness.
9.1.12.
Check the gas group requirements.
9.2. Post-installation
Following the initial installation of the system into a Hazardous Area, the equipment and installation
shall undergo a Detailed Inspection to ensure;
•
The suitability for the hazardous area in which it is installed,
•
That it complies with the relevant system documentation, and
•
That no obvious damage has occurred during installation.
Refer to the Detailed Inspection column on Section 9.4. “Inspection and Test Schedule”.
9.3. Post-commissioning
Following commissioning, there are three levels of inspection required by the standard, these being:
9.3.1.
Detailed Inspection
A Detailed Inspection should be performed on the equipment and installation at the following times:
•
Following commissioning of any new system,
•
Following any modification or repair to the system to ensure the continued suitability of the
system, and
•
Following any change in area classification or process change on a plant to ensure the safety
requirements remain valid.
Detailed Inspections should be performed in accordance with the "Detailed" column on Section 9.4.
“Inspection and Test Schedule”, and is used to ensure the same level of safety determined by the
Post-Installation Inspection.
Summary of Contents for RCI-4100
