background image

36

Rockwell Automation Publication 1441-UM006A-EN-P - May 2011

Chapter 2

 Run Up/Coast Down Extension Module

Displaying Measurements 
Using a Spectrogram

The Spectrogram plot is a three-dimensional color intensity plot displaying the 
amplitude of spectral components as a function of both time and frequency. 
Typically the horizontal and vertical axes correspond to time and frequency. The 
intensity corresponds to amplitude. 

Set Up the Spectrogram Plot

Follow these instructions to setup the plot.

1.

Select Spectrogram

 

on the RUCD - Display Select screen and press F3 

(Display). 

The RUCD - Spectrogram Setup screen appears.

2.

Select a parameter and press the Right arrow to open a list of parameters.

3.

Select to type in a parameter value.

4.

Press the Left arrow to save your selection. 

Use the descriptions in 

Spectrogram Plot Parameter Descriptions on 

page 37

 to help you configure the parameters.

5.

When you are finished, press F3 (Display) to display the Spectrogram plot.

See

Display the Spectrogram Plot on page 38

 for more information.

Summary of Contents for 1441-DYN25-MRUC



















































Reviews: