24
Rockwell Automation Publication 2715P-UM001C-EN-P - March 2019
Chapter 2
Install the PanelView 5510 Terminal
Required Circuit Port Parameters for USB Peripheral Devices
This product contains USB host ports that comply with hazardous location environments. Field wiring compliance
requirements are provided in compliance with the National Electrical Code, Article 500.
Figure 2 - PanelView 5510 Control Drawing
PanelView 5510 terminals provide two, separately powered USB host ports.
defines the circuit parameters of
these USB host ports.
Application Information
Per the National Electrical Code, the circuit parameters of associated field-wiring apparatus for use in hazardous
locations shall be coordinated with the host product such that their combination remains nonincendive. PanelView 5510
terminals and the USB peripheral devices shall be treated in this manner.
The USB peripheral devices and their associated cabling shall have circuit parameters with the limits given in
for
them to remain nonincendive when used with the PanelView 5510 USB host ports.
If cable capacitance and inductance are not known, use the following values from ANSI/ISA-RP 12.06.01-2003:
C
cable
= 197 pF/m (60 pF/ft)
L
cable
= 0.7 μH/m (0.20 μH/ft)
Nonincendive field wiring must be wired and separated in accordance with 501.10(B)(3) of the National Electrical Code
(NEC) ANSI/NFPA 70 or other local codes as applicable. This associated nonincendive field wiring apparatus has not
been evaluated for use in combination with another associated nonincendive field wiring apparatus.
Nonincendive Field
Wiring Apparatus
Associated Nonincendive Field Wiring Apparatus
PanelView 5510 Host Product
USB Peripheral Device
USB Peripheral Device
USB Host Port
USB Host Port
Table 9 - Circuit Parameters for USB Host Ports
Parameter
Value
Parameter Definition
V
oc (USB)
5.25V DC
Open circuit voltage of each host USB port.
The maximum applied voltage rating, V
max (peripheral)
, of each USB peripheral device shall be greater
than or equal to V
oc (USB)
.
V
max (peripheral)
≥ V
oc (USB)
(as appropriate)
I
sc (USB)
1.68 A
Maximum output current of each host USB port.
The maximum current,
I
max (peripheral)
, to which each USB peripheral device can be subjected, shall be
greater than or equal to
I
sc (USB).
I
max (peripheral)
≥
I
sc (USB)
C
a (USB)
10 μF
This value is the maximum total capacitance that can be connected to each USB host port. The total
capacitance of each USB peripheral device and its associated cable must not exceed the indicated
value.
The maximum total capacitance, C
i (peripheral)
, and cable capacitance of each separate USB peripheral
device shall be less that or equal to C
a (USB)
.
C
i (peripheral)
+ C
cable(USB)
≤ C
a (USB)
L
a (USB)
15 μH
This value is the maximum total inductance that can be connected to each USB host port. The total
inductance of each USB peripheral device and its associated cable must not exceed the indicated value.
The maximum total inductance, L
i (peripheral)
, and cable inductance of each separate USB peripheral
device shall be less than or equal to L
a (USB)
.
L
i (peripheral)
+ L
cable
≤ L
a (USB)
Summary of Contents for Allen-Bradley PanelView 5510 Series
