17
EN
1
General safety precautions
Warning
: incorrect installation may
cause severe damage or injury.
Read the instructions carefully before
installing the product.
This installation manual is intended for qualified
personnel only. ROGER TECHNOLOGY cannot be
held responsible for any damage or injury due to
improper use or any use other the intended usage
indicated in this manual.
Installation, electrical connections and
adjustments must be performed by qualified
personnel, in accordance with best practices and
in compliance with applicable regulations. Before
installing the product, make sure it is in perfect
condition.
Disconnect the mains electrical power before
performing any work. Only use original spare parts
when repairing or replacing products.
The packaging materials (plastic, polystyrene,
etc.) should not be discarded in the environment or
left within reach of children, as they are a potential
source of danger.
WARNING! Handle electronic parts and
terminals with extreme care, as these parts are
highly sensitive to static electricity.
2
Product description
The boom connection
ACS/BA/60 - ACS/BA/68
is a
safety device for disengaging the booms of the BIONIK
barriers.
Following an impact to the boom, the system disengages,
protecting the boom and the barrier against serious
damage. The built-in sensor interrupts the operation of
the automation system.
The connection of the detachable boom
ACS/BA/60 -
ACS/BA/68
can be used with the firmware version r3.50
(or later) of the control unit
CTRL
or with the firmware
version c1.30 (o later) of the control unit
CTRL/P.
3
Technical characteristics of
the magnetic sensor
TECHNOLOGY USED
Unipolar, HALL
effect sensor
MAINS POWER VOLTAGE
24Vdc ±15%
CURRENT ABSORPTION
8mA
OUTPUT TYPE
Open Collector
MAXIMUM VOLTAGE
APPLICABLE AT THE OUTPUT
12Vdc
OPERATING TEMPERATURE
-20°C
+55°C
4
Installation
The
ACS/BA/60
system uses the
BA/60/3
round boom,
up to 3 meters in length.
The
ACS/BA/68
system uses the
BA/60/3
elliptical
boom, up to 3 meters in length,
BA/60/4
elliptical boom,
up to 4meters in length.
To install the
ACS/BA/60
, see pag 3 for BI/004 or pag 4
for BI/001PC - BI/001PE - BI/004HP.
To install the
ACS/BA/68
, see pag 5-6 for BI/004 or pag
7-8 for BI/001PC - BI/001PE - BI/004HP.
4.1
BI/004 installation with ACS/BA/60
(pag. 5)
1. Pass the connecting cable through the crankshaft
and make it come out from the opposite side.
2. Partially tighten
the 12 screws [
B
] M10x16 as shown
in detail
1
.
3. Insert the rod holder [
A
] into the motor shaft.
4. Tighten the 12 screws [
B
] M10x16 until
fully secured
.
5. Insert the boom [
C
] BA/60/3 in the cylindrical bracket
[
E
] and fasten it with the 4 self-tapping screws [
F
].
NOTE: Before inserting the boom into the bracket,
apply the supplied adhesive tape [
D
].
6. Insert the rod fully inside the rod support [
A
] and
fasten it with the screw [
G
] M12x100.
7. Put the cover [
H
] and fasten it with the 2 screws
supplied.
8. Pass the connecting cable through the centre of the
linkage lever [detail
I
].
9. Fasten the cable with the cable clamp located inside
the barrier supporting structure [detail
L
]
10. Feed the cable into the control unit [detail
M
],
ensuring that the cable does not interfere with the
movements of the automation system.
11. Continue with the electrical connections.
4.2
BI/001PC-BI/001PE-BI/004HP
installation with ACS/BA/60 (pag. 6)
1.
Remove the flange [
A
] from the crankshaft.
NOTE
: This product must be disposed of only
by qualified technical personnel, following
suitable procedures. Observe local legislation for
differentiated refuse collection.
2. Pass the connecting cable through the crankshaft
and make it come out from the opposite side.
3. Fasten the [
B
] boom support to the crankshaft with
the 4 [
C
] M12x80 screws.
4. Insert the boom [
D
]
BA/60/3
in the cylindrical bracket
[
F
] and fasten it with the 4 self-tapping screws [
G
].
NOTE: Before inserting the boom into the bracket,
apply the supplied adhesive tape [
E
].
5. Insert the rod fully inside the rod support [
B
] and
fasten it with the screw [
H
] M12x100.
6. Put the cover [
I
] and fasten it with the 2 screws
Summary of Contents for ACS/BA/60
