DE
111
Einstellung für die Erkennung von Hindernissen (Quetschschutz)
Das Ansprechen der Hinderniserkennung während der Schließbewegung verursacht das erneute Öffnen.
Das Ansprechen der Hinderniserkennung während der Öffnungsbewegung verursacht die Umkehr der Bewe-
gung nur dann, wenn das Hindernis in den ersten 60° des Bewegungsradius erkannt wird.
Die Versuche zum erneuten automatischen Schließen der Schranke werden durch den Parameter
festgelegt.
HINWEIS:
Die verfügbaren Werte können durch die Einstellung des Parameters
$
begrenzt sein.
= Minimale Zeit bis zum Ansprechen (maximale Sensibilität) ...
= Maximale Zeit bis zum Ansprechen
(minimale Sensibilität).
Die Schranke bleibt für maximal 5 Sekunden am Hindernis stehen, bevor sich die Bewegungsrichtung ändert.
Einstellung Beschleunigung zu Beginn der Öffnungsbewegung
Einstellung Beschleunigung zu Beginn der Schließbewegung
= Die Schranke beschleunigt schnell zu Beginn der Bewegung ...
= Die Schranke beschleunigt lang-
sam und allmählich zu Beginn der Bewegung.
HINWEIS:
Die verfügbaren Werte können durch die Einstellung des Parameters
$
begrenzt sein.
Einstellung Geschwindigkeit beim Öffnen (%)
Einstellung Geschwindigkeit beim Schließen (%)
= 10% Minimale Geschwindigkeit ...
= 100% Maximale Geschwindigkeit.
HINWEIS:
Die verfügbaren Werte können durch die Einstellung des Parameters
$
begrenzt sein.
Einstellung der Annäherungsgeschwindigkeit
Der Parameter regelt die Geschwindigkeit des Motors während der Annäherung an den Öffnungs-/Schließanschlag.
= 10 Motorumdrehungen pro Minute (U/min) ...
= 100 Motorumdrehungen pro Minute (U/min).
Einstellung des Annäherungswegs beim Öffnen
Einstellung des Annäherungswegs beim Schließen
0,5 bis 3 Umdrehungen der Motors mit der unter Parameter
eingestellten Geschwindigkeit.
HINWEIS:
Die verfügbaren Werte können durch die Einstellung des Parameters
$
begrenzt sein.
Einstellung der Anzahl der Versuche des automatischen Wiederschließens nach An-
sprechen der Sicherheitsleiste oder Erkennen eines Hindernisses (Quetschschutz)
Kein Versuch des automatischen Wiederschließens.
1 bis 3 Versuche des automatischen Wiederschließens.
Das automatische Wiederschließen erfolgt nur, wenn die Schranke vollständig geöffnet ist.
Stellen einen geringeren oder gleichen Wert wie Parameter
$
ein.
Einstellung Funktionsweise der Lichtschranke beim Öffnen (FT)
HINWEIS:
Der Parameter wird nicht angezeigt, wenn der Parameter
=
,
,
ist.
DEAKTIVIERT. Die Lichtschranke ist nicht aktiv oder nicht installiert.
STOP. Die Schranke hält an und bleibt bis zum nächsten Befehl stehen.
SOFORTIGE UMKEHR. Wenn die Lichtschranke während der Öffnungsbewegung aktiviert wird, kehrt die
Schranke sofort um.
VORÜBERGEHENDER STOPP. Die Schranke hält so lange an, wie die Lichtschranke verdunkelt ist. Bei Freigabe
der Lichtschranke öffnet sich die Schranke weiter.
VERZÖGERTE UMKEHR. Bei verdunkelter Lichtschranke hält die Schranke an. Bei Freigabe der Lichtschranke
schließt sich die Schranke.
Einstellung Funktionsweise der Lichtschranke beim Schließen (FT)
HINWEIS:
Der Parameter wird nicht angezeigt, wenn der Parameter
=
,
,
ist.
DEAKTIVIERT. Die Lichtschranke ist nicht aktiv oder nicht installiert.
STOPP. Die Schranke hält an und bleibt bis zum nächsten Befehl stehen.
SOFORTIGE UMKEHR. Wenn die Lichtschranke während der Schließbewegung aktiviert wird, kehrt die Schran-
ke sofort um.
VORÜBERGEHENDER STOPP. Die Schranke hält so lange an, wie die Lichtschranke verdunkelt ist. Bei Freigabe
der Lichtschranke schließt sich die Schranke weiter.
VERZÖGERTE UMKEHR. Bei verdunkelter Lichtschranke hält die Schranke an. Bei Freigabe der Lichtschranke
öffnet sich die Schranke.
Summary of Contents for CTRL
