DE
115
Kennnummer
Die Kennnummer besteht aus den Werten der Parameter von
Q
bis
Q
.
ANMERKUNG
: Die in der Tabelle angegebenen Werte dienen nur zur Veranschaulichung.
Q
HW-Version
Beispiel:
Q
Herstellungsjahr
Q
Herstellungswoche
Q
Seriennummer
Q
Q
Q
FW-Version
Q
Version der seriellen Verbindung RS485
Anzeige Bewegungszähler
Die Zahl besteht aus den Werten der Parameter von
R
bis
R
, multipliziert mit 100.
ANMERKUNG
: Die in der Tabelle angegebenen Werte dienen nur zur Veranschaulichung.
R
Durchgeführte Bewegungen
Beispiel:
x 100 = 1.234.500 Bewegungen
R
R
Anzeige Stundenzähler Bewegung
Die Zahl besteht aus den Werten der Parameter von
K
bis
K
.
ANMERKUNG
: Die in der Tabelle angegebenen Werte dienen nur zur Veranschaulichung.
K
Stunden Bewegung
Beispiel:
= 123 Stunden
K
Anzeige Zähler Einschalttage des Steuergeräts
Die Zahl besteht aus den Werten der Parameter von
G
a
G
.
ANMERKUNG
: Die in der Tabelle angegebenen Werte dienen nur zur Veranschaulichung.
G
Einschalttage
Beispiel:
= 123 Tage
G
Passwort
Die Festlegung eines Passworts verhindert Unbefugten den Zugriff auf die Einstellungen.
Bei aktiviertem Passwort (
&3
=
) können die Parameter zwar angezeigt, aber NICHT geändert werden.
Das Passwort ist eindeutig, d. h. nur ein Passwort kann den Antrieb verwalten.
ACHTUNG:
Wenden Sie sich bei Verlust des Passworts an den Kundendienst.
HINWEIS:
Der Parameter wird an der SLAVE-Schranke nicht angezeigt.
3
3
3
3
Verfahren zur Aktivierung des Passworts:
• Die gewünschten Werte für die Parameter
3
,
3
,
3
und
3
eingeben.
• Mit den Tasten UP
a
und/oder DOWN
b
den Parameter
&3
anzeigen.
• Die Tasten
+
und
–
4 Sekunden lang drücken.
• Wenn das Display blinkt, wurde das Passwort gespeichert.
• Das Steuergerät aus- und wieder einschalten. Die Aktivierung des Passworts prüfen (
&3
=
).
Verfahren zur vorübergehenden Entriegelung:
• Das Passwort eingeben.
• Prüfen, dass
&3
=
ist.
Verfahren zum Löschen des Passworts:
• Das Passwort eingeben (
&3
=
).
• Die Werte
3
,
3
,
3
,
3
=
speichern.
• Mit den Tasten UP
a
und/oder DOWN
b
den Parameter
&3
anzeigen.
• Die Tasten
+
und
–
4 Sekunden lang drücken.
• Wenn das Display blinkt, wurde das Passwort gelöscht (die Werte
3
,
3
,
3
und
3
bedeuten "Kein Passwort vorhanden").
• Das Steuergerät aus- und wieder einschalten (
&3
=
).
&3
Passwort schutz
Schutz deaktiviert.
Schutz aktiviert.
Summary of Contents for CTRL
