FR
148
Numéro d'identification
Le numéro d'identification composé des valeurs des paramètres de
Q
a
Q
.
REMARQUE
: les valeurs indiquées dans le tableau sont des valeurs purement indicatives.
Q
Version HW
Exemple :
Q
Année de production
Q
Semaine de production
Q
Numéro de série
Q
Q
Q
Version FW
Q
Version de la communication de série RS485
Affichage compteur manœuvres
Le numéro est composé des valeurs des paramètres de
R
à
multiplié par 100.
REMARQUE
: les valeurs indiquées dans le tableau sont des valeurs purement indicatives.
R
Manœuvres effectuées
Exemple :
x100 = 1 234 500 manœuvres
R
R
Affichage compteur heures manoeuvre
Le numéro est composé des valeurs des paramètres de
K
à
K
.
REMARQUE
: les valeurs indiquées dans le tableau sont des valeurs purement indicatives.
K
Heures manoeuvre
Exemple :
= 123 heures
K
Affichage compteur jours d'allumage de la centrale
Le numéro est composé des valeurs des paramètres de
G
à
G
.
REMARQUE
: les valeurs indiquées dans le tableau sont des valeurs purement indicatives.
G
Jours d'allumage
Exemple :
= 123 jours
G
Mot de passe
La saisie du mot de passe empêche l'accès aux réglages au personnel non autorisé.
Avec mot de passe actif (
&3
=
) on peut afficher les paramètres, mais on ne peut pas en modifier les valeurs.
Le mot de passe est univoque, c'est-à-dire un seul mot de passe peut gérer l'automatisme.
ATTENTION :
En cas de perte du mot de passe, contacter le service assistance.
REMARQUE :
Le paramètre n'est pas visible dans la barrière SLAVE.
3
3
3
3
Procédure d'activation mot de passe :
• Saisir les valeurs souhaitées dans les paramètres
3
,
3
,
3
et
3
.
• Avec les touches UP
a
et/ou DOWN
b
afficher le paramètre
&3
.
• Appuyer pendant 4 s sur les touches
+
et
-
.
• Quand l'écran clignote, le mot de passe a été mémorisé.
• Éteindre et rallumer la centrale. Vérifier l'activation du mot de passe (
&3
=
).
Procédure de déblocage temporaire :
• Saisir le mot de passe.
• Vérifier que
&3
=
.
Procédure d'élimination mot de passe :
• Saisir le mot de passe (
&3
=
).
• Mémoriser les valeurs de
3
,
3
,
3
,
3
=
• Avec les touches UP
a
et/ou DOWN
b
afficher le paramètre
&3
.
• Appuyer pendant 4 s sur les touches
+
et
-
.
• Quand l'écran clignote, le mot de passe a été supprimé (les valeurs
3
3
3
et
3
correspondent à “mot
de passe absent”).
• Éteindre et rallumer la centrale (
&3
=
).
&3
Protection
changement mot de passe
Protection désactivée.
Protection activée.
Summary of Contents for CTRL
