FR
151
16
Signalisations alarmes et anomalies
DÉFAUTS
SIGNALISATION
ALARME
CAUSE PROBABLE
ACTION CORRECTIVE
La barrière ne
s'ouvre pas ou ne se
ferme pas.
LED
POWER
éteinte
Absence de l'alimentation.
Vérifier le câble d'alimentation.
LED
POWER
éteinte
Fusibles grillés.
Remplacer le fusible.
Il est recommandé d'extraire et de réinsérer le fusible uni-
quement en l'absence d'alimentation de secteur.
)86(
Fusible F1 grillé.
Si la centrale est en modalité
batterie la signalisation n'est
pas visible.
Remplacer le fusible.
Il est recommandé d'extraire et de réinsérer le fusible uni-
quement en l'absence d'alimentation de secteur.
2) 6W
Anomalie dans la tension
d'alimentation d'entrée.
Initialisation de la centrale
échouée.
Couper l'alimentation, attendre 10 s et remettre l'alimen-
tation.
Si le problème persiste, il est conseillé de remplacer la
centrale de commande.
3U 2W
Détection surintensité dans
l'onduleur.
Appuyer deux fois sur la touche
TEST
ou donner 3 com-
mandes en succession.
VH&2
Mauvais raccordement à SEC1-
SEC2 du transformateur
Échanger la connexion entre SEC1 et SEC2.
G$ W$
Erreur de saisie de données
de course
Vérifier l’équilibrage correct du ressort avec la barrière
débloquée. Appuyer sur TEST et vérifier les éventuelles
sécurités en alarme.
Répéter la procédure d’apprentissage.
Procédure d’étalonnage
échouée (
3+$6
)
Respecter les temps d’étalonnage requis en phase de
procédure d’apprentissage.
Avant de refermer le portillon de déverrouillage, s’assurer
que sur l’écran le signal
3+$6
clignote.
Répéter la procédure d’apprentissage.
Message de modification de
sélection de position de l’au-
tomatisme avec le paramètre
.
DX
SX
D’usine, les barrières sont fournies avec une ouverture à
droite
(position de la barrière par rapport à l’embrasu-
re en regardant vers la trappe d’inspection). Si la position est
modifiée et que le message
'DWD
apparaît :
• Mettre la tige en position 45°.
• Déplacer la position du ressort sur la base du sens d’ou-
verture choisi.
• Appuyer sur PROG jusqu’à ce que le message
'$7$
disparaît et
$3S
apparaisse sur l’écran.
Répéter la procédure d’apprentissage.
Moteur non raccordé.
Vérifier le câble moteur.
EU($
Système BreakAway en état
d'alarme.
• Vérifier le réglage du par.
.
• Vérifier le bon branchement du système ACS/BA/60 à
la centrale.
• Raccrocher la barre.
• Évaluer le remplacement de la barre si elle est endom-
magée.
Exemple :
HH
HH
Erreur dans les paramètres
de configuration.
Paramétrer correctement la valeur de configuration et la
sauvegarder.
...Suite
Summary of Contents for CTRL
