ES
164
7
Comandos y accesorios
Si no están instaladas las funciones de contraseña con contacto N.C. se han de conectar con
puente a los bornes COM, o desactivarlas modificando los parámetros
,
,
.
En instalaciones de dos barreras contrapuestas las conexiones a los mandos y a los accesorios han
de efectuarse en la central de mando MASTER. En la central SLAVE se han de conectar el borde
sensible y el comando de STOP, si lo hubiera.
LEYENDA:
N.A. (Normalmente Abierto) .
N.C. (Normalmente Cerrado).
CONTACTO
DESCRIPCIÓN
11(+SC) 10(COM)
Testigo de barrera abierta/cerrada 24 Vcc 3 W.
El funcionamiento del testigo está regulado por el parámetro
$
.
11(+SC) 13(COM)
Conexión para test de fotocélulas y/o economizador de baterías (fig. 5-6).
La alimentación de los transmisores (TX) de las fotocélulas puede conectarse al borne
11(SC)
.
Seleccione el parámetro
$
para activar la función de test.
Cada vez que recibe un comando la centralita apaga y enciende las fotocélulas para comprobar el cambio
correcto de estado del contacto.
Además puede conectarse la alimentación de todos los dispositivos exteriores (excluido receptor radio
exterior) para reducir el consumo de las baterías (si las hubiera). Seleccione
$
o
$
. Estas fun-
ciones no están disponibles en la barrera SLAVE en caso de instalaciones de dos barreras contrapuestas.
¡ATENCIÓN!
Si se utiliza el contacto
11(SC)
para el test de fotocélulas o el funcionamiento de economi-
zador de baterías, ya no se podrá conectar un testigo de barrera abierta.
11(+SC) 13(COM)
Conexión de la bombilla del testigo de indicación de anomalía del sensor del sistema para asta con des-
enganche ACS/BA/60 o indicación de anomalía en la alimentación desde batería (batería por agotarse.
(Fig. 9). El nivel de tensión de la batería puede configurarse en el parámetro
.
Conectando un RELÉ en la salida SC puede obtenerse un contacto puro de indicación a un sistema de
control externo (fig. 9).
NOTA
: en instalaciones MASTER - SLAVE, conectar el sistema de control externo en la salida SC de la
central de mando MASTER.
12(+LUCI) 13(COM)
Entrada para conexión luces de señalización en el asta serie
ALED
(opcional). 24 Vcc 12W máx (fig. 3).
14(+24V) 13(COM)
Alimentación para dispositivos exteriores máx 10W. Véase características técnicas.
15(+ES) 17(COM)
Entrada para conexión de electrobloqueo. Véase características técnicas.
16(+LAM) 17(COM)
Conexión intermitente (24 Vcc - 5 W máx).
Se pueden seleccionar la configuración de predestello con el parámetro
$
y los modos de intermitencia
con el parámetro
.
18(COM)-19(LNA)-20(LNB)
CO
M
LNA
LNB
18 19 20
Conexión del cable (3x0,5 mm
2
- longitud máxima 30 m) de comunicación serial RS485 para instalación
de dos barreras contrapuestas MASTER y SLAVE (a partir de la versión de firmware
Q
o siguientes).
Conexiones.
• Conectar
los
bornes
COM-LNA-LNB
de la barrera MASTER a los bornes correspondientes de
la barrera SLAVE.
•
La barrera MASTER es la barrera que se abre (completamente) al recibir la orden de apertura
parcial (PED).
•
Seleccione el parámetro
$
para la barrera MASTER y
$
para la barrera SLAVE.
•
Tras haber modificado las configuraciones del parámetro
$
cortar y volver a conectar la ali-
mentación.
•
Todos los mandos, las fotocélulas y la orden de STOP general han de conectarse a la barrera
MASTER. Los bordes sensibles y los dispositivos BreakAway ACS/BA/60 deben conectarse a las
respectivas barreras.
•
Puede conectarse una posible orden de STOP auxiliar en la barrera SLAVE. Si no se utiliza, conec-
tar con puente los bornes
21(ST)-22(COM)
en la central de mando SLAVE.
•
Todos los parámetros, excepto
$
,
y
, han de seleccionarse en la central MASTER.
•
El aprendizaje de la carrera ha de efectuarse en ambas barreras, tras seleccionar los parámetros
según se desee y en función del tipo de instalación.
•
Las señales de alarma pueden verse en la pantalla de las centrales correspondientes.
Summary of Contents for CTRL
