ES
183
15
Señalización de las entradas de seguridad y de los
comandos (Modo TEST)
Si no se ha activado ningún comando de forma voluntaria, pulse la tecla TEST y compruebe lo siguiente:
PANTALLA
CAUSA POSIBLE
INTERVENCIÓN DESDE
SOFTWARE
INTERVENCIÓN TRADICIONAL
U
(rS)
La barrera MASTER está bloqueada.
Contacto de PARADA de la barrera
MASTER abierto.
(La señal puede verse en la barrera
SLAVE).
-
Compruebe el pulsador/contacto de STOP
de la central MASTER.
Instale un pulsador de STOP (N.C.) o co-
necte con puente el contacto ST con el
contacto COM de la central MASTER.
EU
Sistema de soporte de asta con des-
enganche activado, no conectado o
conexión incorrecta.
Controlar las configuraciones del
parámetro
.
Controlar que la conexión del sistema a la
central sea correcta
Contacto STOP de seguridad abierto.
-
Compruebe el pulsador/contacto de STOP.
Instale un pulsador de STOP (N.C.) o co-
necte en puente el contacto ST con el
contacto COM.
Dispositivo de desbloqueo abierto.
-
AGILIK-KB-BI/004HP-BI/006-BI/008
Cierre con la llave dando dos vueltas com-
pletas hacia la derecha.
Compruebe la conexión al microinterruptor
de desbloqueo.
BIONIK4
Cerrar la tapa de desbloqueo y girar la
llave.
Compruebe la conexión al microinterruptor
de desbloqueo.
Puertecilla de inspección de la barrera
abierta.
-
Cierre la puertecilla de inspección de la
barrera.
Compruebe la conexión al microinterruptor.
Borde sensible
COS
no conectado o
conexión incorrecta.
Si no se utiliza o se desea deshabili-
tar, seleccione el parámetro
.
Si no se utiliza, conecte con puente el con-
tacto
COS
con el contacto COM.
Fotocélula
FT
no conectada o conexión
incorrecta.
Si no se utiliza o se desea desha-
bilitar, seleccione el parámetro
y
Si no se utiliza, conecte con puente el con-
tacto
FT
con el contacto COM.
Controle la conexión y las referencias al
esquema de conexión.
SS
Si no se produce un comando volunta-
rio, podría ser defectuoso el contacto
o incorrecta la conexión a un pulsador.
-
Compruebe los contactos PP - COM y las
conexiones al pulsador.
&+
-
Compruebe los contactos CH - COM y las
conexiones al pulsador.
DS
-
Compruebe los contactos AP - COM y las
conexiones al pulsador.
SH
-
Compruebe los contactos PED - COM y las
conexiones al pulsador.
2U
Si no se produce un comando volunta-
rio, podría ser defectuoso el contacto o
incorrecta la conexión al temporizador
-
Compruebe los contactos ORO - COM.
El contacto no ha de conectarse con puente
si no se utiliza.
NOTA:
pulse la tecla TEST para salir del modo TEST.
Es aconsejable solucionar las señalizaciones del estado de las indicaciones de seguridad y de las entradas siempre en modo
“intervención desde software”.
Summary of Contents for CTRL
