PT
214
Número de identificação
O número de identificação é composto dos valores dos parâmetros de
Q
a
Q
.
NOTA
: os valores indicados na tabela são puramente indicativos.
Q
Versão HW
Exemplo:
Q
Ano de produção
Q
Semana de produção
Q
Número de série
Q
Q
Q
Versão FW
Q
Versão da comunicação serial RS485
Visualização do contador de manobras
O número é composto pelos valores dos parâmetros de
R
a
R
multiplicado por 100.
NOTA
: os valores indicados na tabela são puramente indicativos.
R
Manobras realizadas
Exemplo:
x100 = 1.234.500 manobras
R
R
Visualização do contador de horas de manobra
O número é composto pelos valores dos parâmetros de
K
a
K
.
NOTA
: os valores indicados na tabela são puramente indicativos.
K
Horas de manobra
Exemplo:
= 123 horas
K
Visualização do contador de dias de ignição da unidade de controlo
O número é composto pelos valores dos parâmetros de
G
a
G
.
NOTA
: os valores indicados na tabela são puramente indicativos.
G
Dias de ignição
Exemplo:
= 123 dias
G
Palavra passe
A configuração da palavra passe impede o acesso às regulações a pessoal não autorizado.
Com a palavra passe ativa (
&3
=
) é possível visualizar os parâmetros, mas NÃO é possível alterar os valores.
A palavra passe é unívoca, isto é, uma única palavra passe pode gerenciar o automatismo.
ATENÇÃO:
Se a palavra passe for extraviada, entrar em contato com o Serviço de Assistência.
NOTA:
O parâmetro não está visível na barreira SLAVE.
3
3
3
3
Procedimento de ativação da palavra passe:
• Introduzir os valores desejados nos parâmetros
3
,
3
,
3
e
3
.
• Com as teclas UP
a
e/ou DOWN
b
visualizar o parâmetro
&3
.
• Premir por 4 s as teclas
+
e
-
.
• Quando o display piscar, a palavra passe terá sido memorizada.
• Desligar e religar a unidade de controlo. Verificar a ativação da palavra passe (
&3
=
).
Procedimento de desbloqueio temporário:
• Inserir a palavra passe.
• Verificar se
&3
=
.
Procedimento de apagamento da palavra passe:
• Introduzir a palavra passe (
&3
=
).
• Memorizar os valores de
3
,
3
,
3
,
3
=
• Com as teclas UP
a
e/ou DOWN
b
visualizar o parâmetro
&3
.
• Premir por 4 s as teclas
+
e
-
.
• Quando o display piscar, a palavra passe terá sido apagada (os valores
3
,
3
,
3
e
3
correspondem a “palavra passe ausente”).
• Desligar e religar a unidade de controlo (
&3
=
).
&3
Proteção contra a alteração da palavra passe
Proteção desativada.
Proteção ativada.
Summary of Contents for CTRL
