32
IT
7
Comandi e accessori
Le sicurezze con contatto N.C. se non installate devono essere ponticellate ai morsetti COM,
oppure disabilitate modificando i parametri
,
,
.
In installazioni di due barriere contrapposte i collegamenti ai comandi e agli accessori devono essere
effettuati sulla centrale di comando MASTER. Sulla centrale SLAVE collegare il bordo sensibile e
l'eventuale comando di STOP.
LEGENDA:
N.A.
(Normalmente
Aperto).
N.C. (Normalmente Chiuso).
CONTATTO
DESCRIZIONE
11(+SC) 10(COM)
Spia barriera aperta/chiusa 24 Vdc 3 W.
Il funzionamento della spia è regolato dal parametro
$
.
11(+SC) 13(COM)
Collegamento test fotocellule e/o battery saving (fig. 5-6).
E’ possibile collegare l’alimentazione dei trasmettitori (TX) delle fotocellule al morsetto
11(SC)
.
Impostare il parametro
$
per abilitare la funzione di test.
La centralina ad ogni comando ricevuto spegne e accende le fotocellule, per verificare il corretto cambio
di stato del contatto.
E’ possibile collegare inoltre, l’alimentazione di tutti i dispositivi esterni (escluso ricevitore radio esterno)
per ridurre il consumo delle batterie (se presenti). Impostare
$
o
$
. Queste funzioni non sono
disponibili nella barriera SLAVE nel caso di installazioni con due barriere contrapposte.
ATTENZIONE!
Se si utilizza il contatto
11(SC)
per il test fotocellule o il funzionamento battery saving,
NON è più possibile collegare una spia barriera aperta.
11(+SC) 13(COM)
Collegamento lampada spia per segnalazione anomalia del sensore del sistema per asta sganciabile
ACS/BA/60
o segnalazione anomalia nell'alimentazione da batteria (batteria in esaurimento. (Fig. 9)
Il livello di tensione della batteria è impostabile al parametro
.
Collegando un RELAY all'uscita SC è possibile avere un contatto puro di segnalazione a un sistema di
controllo esterno (fig. 9).
NOTA
: in installazioni MASTER - SLAVE collegare il sistema di controllo esterno all'uscita
SC
della cen-
trale di comando MASTER.
12(+LUCI) 13(COM)
Ingresso per collegamento luci di segnalazione sull'asta serie
ALED
(opzionale). 24 Vdc 12W max (fig. 3).
14(+24V) 13(COM)
Alimentazione per dispositivi esterni max 10W. Vedi caratteristiche tecniche.
15(+ES) 17(COM)
Ingresso per collegamento elettroblocco. Vedi caratteristiche tecniche.
16(+LAM) 17(COM)
Collegamento lampeggiante (24 Vdc - 5 W max).
E’ possibile selezionare le impostazioni di prelampeggio dal parametro
$
e le modalità di intermittenza
dal parametro
.
18(COM)-19(LNA)-20(LNB)
CO
M
LNA
LNB
18 19 20
Collegamento cavo (3x0,5 mm
2
- lunghezza massima 30 m) di comunicazione seriale RS485 per in-
stallazione di due barriere contrapposte MASTER e SLAVE (dalla versione firmware
Q
o successive).
Collegamenti.
• Collegare i morsetti
COM-LNA-LNB
della barriera MASTER ai relativi morsetti della barriera SLAVE.
• La barriera MASTER è la barriera che apre (completamente) al comando di apertura parziale (PED).
• Impostare il parametro
$
per la barriera MASTER e
$
per la barriera SLAVE.
• Dopo aver modificato le impostazioni del parametro
$
togliere e dare nuovamente alimentazione.
• Tutti i comandi, le fotocellule e il comando di STOP generale devono essere collegati alla barriera
MASTER. I bordi sensibili e i dispositivi BreakAway
ACS/BA/60
devono essere collegati alle rispettive
barriere.
• E' possibile collegare un eventuale comando di STOP ausiliario sulla barriera SLAVE. Se non utilizzato
ponticellare i morsetti
21(ST)-22(COM)
sulla centrale di comando SLAVE.
• Tutti i parametri, tranne
$
,
e
, devono essere impostati sulla centrale MASTER.
• L'apprendimento della corsa deve essere effettuato su entrambe le barriere, dopo aver impostato i
parametri come desiderato e come da tipologia di installazione.
• Le segnalazioni di allarme sono visibili nei display delle rispettive centrali.
Summary of Contents for CTRL
