background image

RWL-1 Operating Manual.doc 

 

2020-03-25 

 

2/18 

 

D

ESIGN AND APPLICATION

 

RWL-1 lock enables read-in access control based on MIFARE proximity cards. The lock can be 

operated in 

Online mode

 within RACS 5 access control system or in 

Offline mode

 as standalone 

device. In the Online mode the wirelessly connected MC16 controller decides if access is granted. In 
the 

Offline mode

, based on the card numbers stored in its memory, the lock decides autonomously if 

the access can be granted. In case of wireless connection failure or disconnection with access 
controller the lock automatically switches from 

Online mode

 to 

Offline mode

The RWL-1 lock consists of two escutcheons with handles and mortise lock. Card reader is installed in 
the external escutcheon while the battery pack is installed in the internal escutcheon. The internal 
handle is permanently coupled with deadbolt thus the door can be always opened from the inside 

regardless of proximity card and batteries charge level. The external handle is separated from the 
deadbolt and moves freely. When the access is granted the electronic module couples the external 

handle with deadbolt and latch to enable door opening. When the door is closed then the deadbolt is 
relocked automatically in order to protect door against unauthorized opening. The RWL-1 lock can be 
optionally equipped with door cylinder and then be opened from the outside with traditional metal 

key. The RWL-1 is equipped with deadbolt position detector and knob switch position detector. 
Optionally the RWL-1 can be equipped with external door contact to monitor door opening. Statuses 

of all detectors are reported to access controller. The wireless lock is supplied with 4 pcs of AA 
batteries. Low battery level can be signalled locally and reported to the access controller. The 

batteries enable two year operation for average 10 card readings per day. 

Depending on door opening direction and handle location on the door leaf the adequate type of RWL-
1 lock must be applied.  

Version 

Description 

RWL-1-LI 

Left hand door 

RWL-1-RI 

Right hand door 

RWL-1-LO 

Left hand reverse door 

RWL-1-RO 

Right hand reverse door 

 

 

Fig 1. RWL-1 lock in inward opening doors while standing outside 

Summary of Contents for RWL-1 series



















Reviews: