Roger RWL-1-SL Operating Manual Download

Page: 10 / 13

RWL-1-SL Operating Manual.doc

2021-12-20

10/13

Load defaults

Restore default settings

Read from File…

Load backup configuration

Send to File...

Save backup configuration

Read from Device

Reads configuration from device

Send to Device

Upload configuration to device

Tab: Credentials

Add

Adds new user

Edit

Edit existing user

Delete

Delete existing user

Delete all

Delete all users

Read from file

Read users list from file

Write to file

Save users list to file

Read from device

Read users list from device

Send to device

Save users list to device

RWL-1-SL configuration parameters in RogerVDM

The table below includes RWL-1-SL configuration parameters which can be modified using RogerVDM
software within low level configuration of device (tab:

Configuration

Parameter

Function

General settings

LED SYSTEM flash after card
read

When option is set then card reading is confirmed with flash on
LED SYSTEM. Default value: Yes.

Short sound after card read

When option is set then card reading is confirmed with short
acoustic beep. Default value: Yes.

LED SYSTEM pulsing when

card close to the reader

When option is set then orange LED SYSTEM pulses whenever card

is detected near the reader. Default value: No.

Battery low level signalisation When option is set then lock signals low battery level by orange

LED SYSTEM indicator pulsing and series of 5 acoustic beeps after

card reading. Default value: Yes.

Buzzer loudness level

The parameter defines loudness level of the built-in buzzer. When
set to zero then buzzer is disabled. Default value: 100%

Standalone mode

Lock pulse [s]

The parameter defines lock opening time when access is granted.
Default value: 2s.

ADD programming card

The card code of the ADD programming card.

DEL programming card

The card code of the DEL programming card.

Backup cards

When option is on, then each user programmed in the lock can
have both

Main card

and

Backup card

. When the option is off then

each user can have the

Main card

only. Default value: Yes.

Card codes protection

When option is set then it is not possible to read user card codes
from the lock’s memory. Once option is set it can be cleared by

memory reset procedure only. The purpose of the option is to

Summary of Contents for RWL-1-SL














Search results

Summary of Contents for RWL-1-SL

Reviews:

Related manuals for RWL-1-SL

Brands by name

Popular brands

Roger RWL-1-SL, Operating Manual

Search results

Summary of Contents for RWL-1-SL

Reviews:

Related manuals for RWL-1-SL

Brands by name

Popular brands