Roger RWL-2 Operating Manual Download

Page: 7 / 17

RWL-2 Operating Manual.doc

2018-06-29

7/17

2,440

2,480

LED indicators

RWL-2 lock is equipped with 4 LED indicators which functions are described in the table below.

LED indicators

Name

Colour

Description

LED RED

Red

Online mode

: the function of this LED is programmed in VISO

management software.

Offline mode

: indicator is blinking when lock waits for the

optional second card reading. If it occurs, lock switches to

Office

mode

LED GREEN Green

Online mode

the function of this LED is programmed in VISO

management software.
In

Offline mode

the indicator is not used.

LED BLUE

Blue

Online mode

: the indicator is controlled by access controller in

accordance with the logic applied in the RACS 5 system.
If the lock switches to

Offline mode

due to communication

failure then LED BLUE is operated as lock was in

Offline mode

except that it blinks instead of steady light.
The indicator blinks slowly if wireless communication is not

configured.
In

Offline

mode

the indicator:

2 sec pulse when access is granted and external
handle is coupled

two 2 sec pulses when access is denied

lights steadily when operates in

Office mode

LED
SYSTEM

Orange

lights steadily in case of lock’s configuration error

pulses slowly in case of low battery level (batteries
must be replaced)

pulses every 2 sec when wireless connection is being
established in

Online mode

Power supply

RWL-2 lock is supplied from 4 pcs of AAA batteries. In case of average 10 operations daily the alkaline

batteries enable 1 year functioning. Low battery level is reported to VISO management software and
additionally it is signalled locally by orange LED SYSTEM pulsing and acoustic signal generated prior to

entering standby mode.

ONFIGURATION

RWL-2 lock can be programmed manually or from PC computer. Manual programming enables card
management for

Offline mode

only. All configuration settings can be setup and edited using

RogerVDM program. Connection to PC requires RUD-1 interface.
Factory new lock is configured for

Offline mode

and includes 2 programming cards (ADD card and DEL

card).

Lock pulse

by default is set to 2 sec while built-in RFID reader is configured to read card serial

numbers (CSN).

Summary of Contents for RWL-2


















Search results

Summary of Contents for RWL-2

Reviews:

Related manuals for RWL-2

Brands by name

Popular brands

Roger RWL-2, Operating Manual

Search results

Summary of Contents for RWL-2

Reviews:

Related manuals for RWL-2

Brands by name

Popular brands