background image

Security Locks SL2000F and SL2000F-VP EN 

 

2020-05-06 

 

Page 

12

 of 

12

 

 

 

Product History 

Version  

Firmware 

Date 

Description 

SL2000F v1.0 

N/A 

11/2009 

Initial release of the product 

SL2000F-VP v1.0  N/A 

11/2009 

Initial release of the product 

SL2000F v2.0 

N/A 

05/2020 

Modifications of electronic components 

SL2000F-VP v2.0  N/A 

05/2020 

Modifications of electronic components 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Contact 

Roger sp. z o. o. sp. k. 

82-400 Sztum 

Gosciszewo 59 

Tel.:  +48 55 272 01 32 Fax: +48 55 272 01 33 

Technical support PSTN: +48 55 267 01 26  

e-mail

biuro@roger.pl

 

Web: 

www.roger.pl

 

The symbol of a crossed-through waste bin on wheels means that the product must be 
disposed of at a separate collection point. This also applies to the product and all 
accessories marked with this symbol. Products labelled as such must not be disposed of 
with normal household waste, but should be taken to a collection point for recycling 
electrical and electronic equipment. Recycling helps to reduce the consumption of raw 

materials, thus protecting the environment. 

Summary of Contents for SL2000F













Reviews: