background image

COMPUTER INSTRUCTIONS

33

HOW TO MAINTAIN THE GM-41002 TREADMILL 

CLEANING

:

Routine cleaning of your treadmill will extend the product's life. 

Warning

: To prevent electrical shock, be sure the power to the treadmill is OFF and the power cord is unplugged 

from the wall electrical outlet before attempting any cleaning or maintenance.  

Important

: Never use abrasives or solvents to clean the treadmill.  To prevent damage to the computer, keep 

liquids away and keep it out of direct sunlight.

After each workout

:  Wipe off the console and other treadmill surfaces with a clean, water dampened soft cloth to 

remove excess perspiration.  

Weekly

:  Use of a treadmill mat is recommended for ease of cleaning.  Dirt from your shoes contacts the belt and 

eventually makes it to underneath the treadmill.  Vacuum underneath treadmill once a week.

DECK LUBRICATION

:

The walking belt has been pre-lubricated at the factory.  However, it is recommended that the walking board be checked 
periodically for lubrication to ensure optimal treadmill performance.  Your treadmill should not have to be lubricated usually 
within the first 400 hours of use.  

Every 2 months of operation lift the sides of the walking belt and feel the top surface of the walking board as far as you can 
reach.  If you feel signs of silicone, no further lubrication is required.  If it feels dry to the touch, follow the instructions below.

Please use 100% Silicon Oil to lubricate your treadmill deck.

To apply lubricant to the walking belt

:

1.

Position the walking belt so that the seam is located on top and in center of the walking board.

2.

Insert the spray nozzle into the spray head of the lubricant can.

3.

While lifting the side of the walking belt, position the spray nozzle between the walking belt and the board 
approximately 6" from the front of the treadmill.  Apply the silicone spray to the walking board, moving from the front 
of the treadmill to the rear.  Repeat this on the other side of the belt.  Spray approximately 4 seconds on each side.

Allow the silicone to "set" for 1 minute before using the treadmill.

Summary of Contents for GM-41002









































Reviews: